GRASS VALLEY K2 SOLO - Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 108

background image

Install software on K2 Dyno Controller

Before you install K2 Dyno Client software you must first uninstall the current version.

1. Copy the directory that contains the K2 Dyno Client software onto a portable USB drive, such

as a Flash drive.

2. Connect the USB drive to the K2 Dyno Controller and copy the Client directory to the K2 Dyno

Controller desktop.

3. In the Client directory, locate and open the following file:

setup.exe

4. Follow the onscreen instructions, and work through each page.

•

If this is the first install after a re-image, enter the K2 Dyno Replay Controller serial number
when prompted.

•

If the K2 Dyno System Configuration Tool opens, do not enter any information. Remove any
text from the serial number field, as it must be blank. Then click

OK

and when prompted

"...number is empty. Continue?", click

OK

.

•

If prompted "...update to new firmware?" click

Yes

, observe progress on the K2 Dyno

Controller Firmware Updater, and when a Success message displays, click

OK

.

5. Click

Next

and

Close

to complete the installation.

6. Remove the portable USB drive, if it is still connected.

7. Restart using standard Windows procedures.

8. When prompted "...back to K2 Dyno mode...?", click

Yes

.

The K2 Dyno Controller restarts.

Install MPEG-2/AVC-Intra field kit

If you are installing an MPEG-2 or AVC-Intra field kit upgrade on one or more or your K2
Summit Production Clients or K2 Solo Media Servers, do so now. Follow the procedure in the
Field Kit Upgrade Instructions document that you received with the field kit.

Make recovery images

After you have upgraded software as instructed in these procedures and verified that your system
is working properly, you should always make a recovery image of each of your upgraded
computers. Use a sequence of tasks similar to those you followed for upgrading software so that
as you take systems offline you manage redundancy, servers, and clients, as appropriate for your
system.

Refer to the Grass Valley product's Service Manual for recovery image procedures.

Deploy control point PC software

Use SiteConfig to upgrade control point software on the K2 control point PC. In most cases, the K2
control point PC is also the SiteConfig control point PC, so you are in effect using SiteConfig to
upgrade software on its own local system.

82

K2 Version 7.3.8 Release Notes & Upgrade Instructions

23 November 2010

Upgrading K2 systems

«
...
80
81
82
83
84
...
»

Содержание K2 SOLO -













































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 SOLO -

Бренд: Qlogic Страницы: 20

Бренд: Avaya Страницы: 19

Бренд: IBM Страницы: 36

Бренд: Fujitsu Страницы: 26

Бренд: Fujitsu Страницы: 56

Бренд: Fujitsu Страницы: 36

Бренд: Fujitsu Страницы: 61

Бренд: Fujitsu Страницы: 30

ETERNUS DX Disk

Бренд: Fujitsu Страницы: 85

Бренд: Fujitsu Страницы: 111

BX630 - PRIMERGY - S2 Dual

Бренд: Fujitsu Страницы: 64

Бренд: Fujitsu Страницы: 68

CELVIN NAS QE707

Бренд: Fujitsu Страницы: 95

BX630 - PRIMERGY - S2 Dual

Бренд: Fujitsu Страницы: 90

D3320 PRIMERGY BX2560 M2

Бренд: Fujitsu Страницы: 80

Бренд: Fujitsu Страницы: 238

1PRIMERGY RX600 S4

Бренд: Fujitsu Страницы: 242

Бренд: Fujitsu Страницы: 374

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды