GRASS VALLEY K2 SOLO - Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 108

background image

Upgrade the MediaFrame Proxy NAS (K2 Nearline SAN) to the compatible version of K2
software. Use SiteConfig and deploy software, using steps similar to those for other systems.

a) Check software on the Nearline SAN's K2 Media Servers.
b) Add software

*.cab

file to the deployment group that contains the K2 Media Servers.

c) Upgrade software on K2 Media Servers via a SiteConfig deployment session.

Upgrade Browse and MediaFrame systems

Prerequisites for this task are as follows:

•

K2 systems are upgraded to the compatible version of K2 system software.

•

Aurora Edit, Ingest, and Playout systems are upgraded to the compatible versions of software.

•

K2 Nearline SAN (NAS) systems are upgraded to the compatible version of K2 system software.

Upgrade your Browse and MediaFrame systems to the compatible versions of software. Refer
to Aurora Browse Release Notes for procedures.

Upgrade other SAN clients

Do this task if:

•

You have clients on the K2 SAN that have not yet been upgraded. This is the case if you have
K2 appliances or other products that use the shared storage of the K2 SAN.

Prerequisites for this task are as follows:

•

You have access to the software installation files for this release. Procure the files via the
appropriate distibution method, such as download, CD-ROM, network drive, or external drive.

Refer to upgrade procedures for K2 clients and similarly upgrade all remaining client devices
on the K2 SAN.

NOTE: You must restart after installing K2 software.

Make recovery images

After you have upgraded software as instructed in these procedures and verified that your system
is working properly, you should always make a recovery image of each of your upgraded
computers. Use a sequence of tasks similar to those you followed for upgrading software so that
as you take systems offline you manage redundancy, servers, and clients, as appropriate for your
system.

Refer to the Grass Valley product's Service Manual for recovery image procedures.

Upgrading stand-alone K2 systems with SiteConfig

This section contains the tasks for using SiteConfig to upgrade stand-alone K2 systems to this release
of K2 software.

Work through the tasks sequentially to complete the upgrade.

64

K2 Version 7.3.8 Release Notes & Upgrade Instructions

23 November 2010

Upgrading K2 systems

«
...
62
63
64
65
66
...
»

Содержание K2 SOLO -













































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 SOLO -

NEAX2000 IVS Series

Бренд: NEC Страницы: 160

Бренд: LTS Страницы: 5

UniServer R4300 G5

Бренд: H3C Страницы: 16

4 Ch Video Sever

Бренд: Video Server Страницы: 34

Бренд: Seyeon Страницы: 10

Бренд: LOYTEC Страницы: 4

Бренд: Digi Страницы: 118

DL380 Gen 10 AI

Бренд: Bosch Страницы: 18

Бренд: Bosch Страницы: 48

Бренд: Bosch Страницы: 44

DECT Server 2500

Бренд: SpectraLink Страницы: 27

Бренд: Black Box Страницы: 3

Бренд: Blonder tongue Страницы: 20

LANTIME/SHS/BGT

Бренд: Meinberg Страницы: 5

PROXYSERVER MTPSR1-120

Бренд: Multitech Страницы: 110

ProxyServer MTPSR3-200

Бренд: Multitech Страницы: 130

Бренд: QNAP Страницы: 16

Бренд: Inspur Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды