GRAPHTEC GL820 Скачать руководство пользователя | Manualshive

Страница: 17 / 60

background image

GL820-UM-251-9370

3-5

3. DISASSEMBLY AND REASSEMBLY

3.5 Replacing the Main Control Board

Disassembly

(1)  Remove the input terminal unit from the main unit (See Section 3.2).
(2)  Remove the side pads from the main unit (See Section 3.3).
(3)  Disassemble the top cover assembly and the bottom case assembly (See Section 3.4).
(4)  Disconnect the LCD flexible cable from the main control board.
(5)  Remove the two M2L6 self-tapping screws holding the main control board from the top cover assembly.
(6)  Disconnect the connector between the main control board and the control panel board and then remove

the top cover assembly.

M2L6 self-tapping screw

LED flexible cable

Main control board

Top cover assembly

Core

Fixing tape

Re-assembly

(1) Re-assemble the main control board in the reverse order in which it was disassembled.

«
...
15
16
17
18
19
...
»

Содержание GL820





























































Отзывы:

Нет отзывов

Похожие инструкции для GL820

Бренд: NexSens Technology Страницы: 62

Бренд: Racelogic Страницы: 20

Бренд: EasyLog Страницы: 2

Бренд: Capetti Elettronica Страницы: 9

Бренд: Fluke Страницы: 80

Бренд: Racelogic Страницы: 4

AnaBat Roost Logger

Бренд: TiTLEY Scientific Страницы: 4

MODAT-550A Series

Бренд: IEI Technology Страницы: 79

Бренд: Teac Страницы: 69

Бренд: Omega Страницы: 5

Бренд: TESTO Страницы: 2

0572 2200 Series

Бренд: TESTO Страницы: 27

Бренд: Spotsee Страницы: 115

Бренд: ExtraHop Страницы: 9

FlashLink 40909

Бренд: DeltaTRAK Страницы: 4

Бренд: Cesinel Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды