manualshive.com logo in svg

GRAPHTEC GL820, Руководство по обслуживанию

GRAPHTEC GL820 - Многофункциональный графический регистратор данных, предназначенный для измерения и мониторинга различных параметров. Для быстрого старта используйте бесплатное руководство по эксплуатации, которое можно скачать с manualshive.com. Управляйте данными с легкостью и надежностью благодаря этой высокотехнологичной модели.

Поделиться
Скачать
background image

GL820-UM-251-9370 

2-1

2.  UPGRADING THE FIRMWARE

The version of your GL820’s firmware can be upgraded by rewriting the flash ROM on the pertinent circuit 
boards. You can upgrade the firmware by loading the update program to a USB memory device.

2.1  Note for the firmware upgrading

•  Save the measuring condition to the internal memory or the USB memory before the firmware upgrade.
•  Don't turn off the power during upgrading the firmware.

2.2  How to Upgrade the GL820 Flash ROM from the USB memory device

Preparations for the upgrade

Firmware  :MainVerxxxRevxxxxAxx.GL820 

←

 Main Program file for GL820

 

:PatternVerxxxRevxxxxAxx.GL820

←

 Font file for GL820

(1)  Connect the AC adapter for the GL820.
(2)  Turn on the GL820.
(3)  Copy the two files to a USB memory device from the computer.
 

(Copy the two main program files to root directory of a USB memory. Do not copy them to any folder.)

How to upgrade

(1)  Insert the USB memory device containing the main upgrade program into the GL800's USB port.

Содержание GL820





























































Отзывы:

Нет отзывов

Похожие инструкции для GL820

Davis Instruments WeatherLink Getting Started Manual preview
WeatherLink
Бренд: Davis Instruments Страницы: 16
Lotek PinPoint Commander User Manual preview
PinPoint Commander
Бренд: Lotek Страницы: 22
OVARRO XiLOG 4G/IOT User Manual preview
XiLOG 4G/IOT
Бренд: OVARRO Страницы: 42
hager HTG410H Installation Manual preview
HTG410H
Бренд: hager Страницы: 84
Elster Instromet DL210 Operating Manual And Installation Instructions preview
DL210
Бренд: Elster Instromet Страницы: 135
Blumax GPS-4044 User Manual preview
GPS-4044
Бренд: Blumax Страницы: 36
retmon DCT200 Quick Start Manual preview
DCT200
Бренд: retmon Страницы: 2
Vaisala CWL100 Quick Manual preview
CWL100
Бренд: Vaisala Страницы: 21
MadgeTech MadgeNET RFTemp2000A Product User Manual preview
MadgeNET RFTemp2000A
Бренд: MadgeTech Страницы: 16
Tamam tadbir MIR 6000 Series User Manual preview
MIR 6000 Series
Бренд: Tamam tadbir Страницы: 27
Lascar Electronics EL-USB Series Troubleshooting preview
EL-USB Series
Бренд: Lascar Electronics Страницы: 4
G-Tek LM Pro RF Operating Manual preview
LM Pro RF
Бренд: G-Tek Страницы: 14
G-Tek LM Pro T051 Operating Manual preview
LM Pro T051
Бренд: G-Tek Страницы: 25
Hantek 365A User Manual preview
365A
Бренд: Hantek Страницы: 40
RST Instruments DT2306 Manual preview
DT2306
Бренд: RST Instruments Страницы: 23
Onset Hobo UX90-001 Series Manual preview
Hobo UX90-001 Series
Бренд: Onset Страницы: 5
Onset HOBO U30 GSM User Manual preview
HOBO U30 GSM
Бренд: Onset Страницы: 38
SATO SK-L751-21 Instruction Manual preview
SK-L751-21
Бренд: SATO Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды