manualshive.com logo in svg

GRAPHTEC GL820, Руководство по обслуживанию

Поделиться
Скачать
GRAPHTEC GL820 Скачать руководство пользователя страница 42

GL820-UM-251-9370 

5-6

5. INSPECTION AND CHECK PROCEDURES

5.2  Voltage Measurement Accuracy

Supply the reference voltage or frequency determined for each measurement range, and then check the 
voltage accuracy.

Preparation

• Have a voltage generator on hand that can output voltage up to 50 VDC (using four-digit output).
• Mutually connect the ground terminals of the voltage generator and the GL820 prior to initiating 

measurement.

• Set the AC Line cycle setting of the GL820 to the same cycle as that of your AC line.
• Set the Sampling setting of the GL820 to at least 1 sec or longer.

Wiring connection

Same wiring connection as Setup1. (See Setup1 procedure)

Setting procedure

(1)  Load the condition settings file "GL820ConditionVolt.CND" from the USB memory device.

Measurement procedure

(1)  Press the [MENU] key to display the menu shown below.

(2)  Move the cursor to the Range position of channel 1.
(3)  Press the [ENTER] key to display the menu shown below, and then select the reference voltage range.

Содержание GL820





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды