grandimpianti S80 ELECTRONIC, Инструкция по установке и эксплуатации

Страница: 13 / 47

13
YEARLY CHECK
Grease the chain.
Being greased for life, the reduction motor unit
needs no maintenance.
Gas springs do not need any maintenance either.
Make sure that the connecting screws which
fasten the power supply wires to the connectors
and the main terminal board are tight.
PRIOR TO SWITCHING THE MAIN
CUTOUT SWITCH ON THE WALL BACK
ON, FIT ALL PREVIOUSLY REMOVED
PANELS BACK INTO PLACE.
INSTRUCTIONS FOR THE
REPLACEMENT OF THE ENTIRE
COVER (see fig 4 on page 3 5 and the
relevant description on page 1 1 )
Untie the cotton sheet and take off the entire
old cover as far as the metal sheet of the roller.
To replace the roller cover, poke a tool (e.g. a
big screwdriver) into the ad-hoc hole marked
by position 3 of fig. 4 until it sticks through.
When the tool is so inserted and the pedal is
pressed, the basin will stay lifted. This will
allow the replacement of the roller lining with
no damage to the press basin’s ironing surface.
Then take a new roll of steel-wool. Cut one end
of it diagonally with a pair of scissors and slip
it into the slot on the left side of the roller.
Attention!
While uncovered, the roller must by no
means come into contact with the basin, as
this would damage it inevitably.
Build three steel-wool layers. Having reached
the right side of the roller, cut the steel-wool
diagonally arranging it very carefully on the
head of the roller. The steel-wool must be held
tight, from the beginning to the end of this job.
Let go of the pedal and remove the tool that has
been poked into the ad-hoc hole.
Set thermostat temperature to 100°C and make
the roller turn for approximately ten minutes
until the first part of the layer has completely
settled. Wait until the temperature drops below
50°C and position the flannel layer.
Lower the basin in order to entirely wrap the
flannel layer, then raise the basin again and lift
up an edge of the flannel layer of about 100
mm, and slip the cotton sheet in correctly.
The sheet must be centred on the roller and
inserted from the narrow side. The strings must
be at the sides of the ironer, the seams facing
downwards.
Allow the roller to turn for a few minutes until
the entire cover has stretched out.
Pull the strings moderately until the sheet sits
on the heads of the roller and then tighten and
slip them under the hem of the sheet itself.
8.4 IDENTIFYING AND ORDERING
SPARE PARTS
Refer to the drawings, the exploded view of the
appliance and the spare-part list to identify the
code numbers of spare parts. Send the
manufacturer a customary written order
including the code number and description
of the spare part. Report also the model,
serial number, power supply voltage and
frequency of your appliance.
9. HOW TO DISMANTLE AND
DISPOSE OF THE APPLIANCE
When the appliance is no longer to be used,
dismantle it and dispose of the components
as indicated in paragraph 3. Sort out the
various components of the appliance in
accordance with the waste disposal standards
in force in your country, so as to dispose of
them separately or recycle them
appropriately. All machine parts can be
considered as solid urban waste, except for
the metal parts which are not regarded as
special waste in most European countries.
10. HOW TO ORDER WEAR PARTS
- Steel wool, code 53GI 100011
- S80 sheet, code = 53 GI 701014
- Rough flannel for S80, code =53 GI
701015.
INFORMATION TO USERS
pursuant to article 13 of law decree 25 July
2005, nr. 151 relating to “Implementation
of Directives 2002/95/EC, 2002/96/EC and
2003/108/EC concerning the reduction in
the use of hazardous substances in electric
and electronic apparatus, as well as waste
disposal”
The deleted dustbin symbol on the appliance
indicates the product must be disposed of
separate from other wastes once it reaches
the end of its life cycle.
Once the appliance has reached the end of
its life cycle, the user must therefore take it
to a suitable pre-sorted waste centre for
electronic and electro-technical appliances,
or return it to the dealer on purchasing a new
similar appliance, on a one for one basis.
Adequate pre-sorted waste collection before
subsequently sending the appliance for
recycling, treatment and environmentally
compatible disposal helps avoid possible
negative effects on the environment and
health and favours the recycling of the
materials making up the appliance.
Unlawful disposal of the product by the user
is punishable by the administrative sanctions
indicated in law decree nr. 22/1997 (article
50 and following articles of law decree nr.
22/1997)