Graco Reactor E-8p 3A1602H Скачать руководство пользователя страница 6

Страница: 6 / 58

Warnings

3A1602H

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See

Technical Data

in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See

Technical Data

in all

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about
your material, request MSDS from distributor or retailer.

• Do not leave the work area while equipment is energized or under pressure. Turn off all equipment

and follow the

Pressure Relief Procedure

when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine

manufacturer’s replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,

follow the

Pressure Relief Procedure

and disconnect all power sources.

BURN HAZARD

Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe
burns:

• Do not touch hot fluid or equipment.

WARNING

Содержание Reactor E-8p 3A1602H



























































Результаты поиска

Содержание Reactor E-8p 3A1602H

Отзывы:

Похожие инструкции для Reactor E-8p 3A1602H

Бренды по названию

Популярные бренды

Graco Reactor E-8p 3A1602H, Инструкция - Каталог запасных частей

Результаты поиска

Содержание Reactor E-8p 3A1602H

Отзывы:

Похожие инструкции для Reactor E-8p 3A1602H

Бренды по названию

Популярные бренды