Graco Reactor E-8p 3A1602H Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 58

Graco Reactor E-8p 3A1602H Скачать руководство пользователя страница 14

Setup

14

3A1602H

Lock/Unlock Handle

Lock the handle when the sprayer is moved, laid on its
side, or turned upside down.

Unlock

To unlock the handle, remove lanyard and locking pin
from cart handle. Pull on handle to extend cart handle
and move sprayer.

Lock

To lock the handle, press down handle pins and slide
cart handle through tubes. Insert pin through cart handle
and lock with lanyard.

Install 38 mm Spout Adapter

The sprayer is supplied with a 40 mm spout adapter.
Install 38 mm spout adapters if necessary.

1.

Loosen containment knob.

2.

Remove suction tube caps and place in contain-
ment tray.

3.

For installation instructions, see

Spout Adapter

,

page 45.

Install Desiccant Dryers

1.

Use needle nose pliers to remove two plugs (P)
from the dryer (73).

2.

Remove plug from adapter housing (57).

3.

Screw the dryer into the adapter housing (57) hand-
tight only. Do not overtighten.

F

IG

. 3

F

IG

. 4

ti17513a

ti17514a

F

IG

. 5: Spout Adapters

F

IG

. 6: Desiccant Dryer Installation

ti18063a

Black

Silver

40 mm

38 mm

ti17475a

P

P

57

73

«
...
12
13
14
15
16
...
»

Содержание Reactor E-8p 3A1602H



























































Отзывы:

Нет отзывов