Graco Reactor E-8p 3A1602H Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 58

Graco Reactor E-8p 3A1602H Скачать руководство пользователя страница 10

Overview

10

3A1602H

Overview

The Reactor E-8p is a portable, electric-powered, 1:1
mix ratio proportioner. It is for use with formulated
no-heat polyurethane foams that may be applied with
impingement mix spray guns and for use with polyurea
joint fill materials that may be applied with static mix
guns.

Severe duty, positive displacement reciprocating piston
pumps meter fluid flow to the gun for mixing and apply-
ing. When set to recirculation mode, the Reactor E-8p
will circulate fluids back to the supply pails.

An electronic processor controls the motor, monitors
fluid pressures, and alerts the operator if errors occur.
See

STATUS Indicator

, page 12, for further informa-

tion.

The Reactor E-8p has two recirculation speeds: slow
and fast, and an adjustable pressure output.

Slow Recirculation

•

Use for pump priming.

Fast Recirculation

•

Use for flushing.

•

Use for pump priming.

Pressure Adjust

Automatically maintains selected pressure output for
spraying.

«
...
8
9
10
11
12
...
»

Содержание Reactor E-8p 3A1602H



























































Отзывы:

Нет отзывов