Graco E-Flo 333587D Скачать руководство пользователя страница 97

Страница: 97 / 110

Integration

333587D

Power Reset Diagram

Heat CGM Timing Diagram

Power Reset

Automation Inputs (E-Flo SP Outputs)

Active

Pump

Inactive

Pump

Pump Heartbeat To PLC

System Active

Automation Control Ready

Pump PLC Lockout/Control Active

Automation Outputs (E-Flo SP Inputs)

¸6\VWHP(QDEOH5HPRWH6WDUW5HTXHVW

¸3XPS3/&/RFNRXW&RQWURO5HTXHVW

Notes:

Tag ID

When in Tandem mode, sending the Automation Output will result in the
information being sent to both active and inactive pumps.

Offline

Heat CGM Timing

Automation Inputs (E-Flo iQ Outputs)

Heat Heartbeat To PLC

92 127

Sy stem Heat Enabled

93 128

Heat PLC Lockout/Control Activ e

94 129

Automation Outputs (E-Flo iQ Inputs)

Sy stem Heat Enabled Request

Sy stem Heat Disable Request

Heat PLC Lockout/Control Request

Other Automation Outputs Instances

Notes:

භ

"Sy

stem Heat Enabled Request", "System Heat Disable Request" and "Heat Module Data Exchange Desired Element"

will be accepted with out the

"Heat PLC Lockout/Control" set high, any other Automation Outputs Instance needs to have

the "Heat PLC Lockout/Control" set high
f

or the Automation Output Instance to be accepted by the iQ Heat Controller

භ

Other Automation Output Instances includes, "Heat On Request", "Heat Of

f Request", "Heat Setback Request",

"Acknowledge/Clear Heat Errors",

and "Heat Module Data Exchanged Desired Element Value"

Tag ID

Содержание E-Flo 333587D















































































































Результаты поиска

Содержание E-Flo 333587D

Отзывы:

Graco E-Flo 333587D, Операция, Страница: 97 / 110

Результаты поиска

Содержание E-Flo 333587D

Отзывы: