Graco E-Flo 333587D Скачать руководство пользователя страница 5

Страница: 5 / 110

Dispense System Components

333587D

Dispense System Components

NOTE:

The Heated option for the E-Flo iQ system is for warm melt applications with a maximum temperature of 70° C

(158° F).

iQ Ram Supply Units

Check the identification plate (ID) on the back of the ram post near the Power Junction Box (AJ) for the seven-digit part

number of the iQ ram supply unit. Use the following matrix to define the construction of the unit, based on the seven dig

its. For example, Part No.

EZC2422

represents an electric supply unit (

), a carbon steel Check-Mate 200 Severe Duty

displacement pump (

), a 3 in. ram (

), a 5-gallon platen with a neoprene seal (

), and an ADM (

The digits in the following matrix do not correspond to the reference numbers in the Parts drawings and lists.

KEY:

First

and

Second

Digit

Third and Fourth Digit

Fifth Digit

Sixth Digit

Seventh

Digit

Check-Mate Pump Options

Ram Options

Platen and Seal Options

Interface

Options

Size

Pump

Material

Heated/

Ambient

Nam

Size

Drum

Size

Style

Platen

Size

Platen

Materia

Seal

Material Wiper

Heated/

Ambient

Interfac

(Electric

Supply

System)

200cc

Ambient

D60

3 in.

20 L

(5 Gal)

Ambi

ent

20 L

(5 Gal) CST/AL Neoprene

Single

Ring

Ambient

ADM

200cc

Heated

<70° C

D200 3 in.

200 L

(55 Gal)

Ambi

ent

20 L

(5 Gal) CST/AL Neoprene

Single

Ring

Heated

<70° C

4 No ADM

200cc

Ambient

D200s 6.5 in.

200 L

(55 Gal)

Ambi

ent

20 L

(5 Gal) CST/AL

EPDM

Single

Ring

Ambient

200cc

Heated

<70° C

D60

3 in.

20 L

(5 Gal)

Heated

<70° C

20 L

(5 Gal) CST/AL

EPDM

Single

Ring

Heated

<70° C

D200 3 in.

200 L

(55 Gal)

Heated

<70° C

200 L

(55

Gal)

Neoprene

Double

Ring

Ambient

D200s 6.5 in.

200 L

(55 Gal)

Heated

<70° C

200 L

(55

Gal)

Neoprene

Double

Ring

Heated

<70° C

200 L

(55

Gal)

EPDM

Double

Ring

Ambient

200 L

(55

Gal)

EPDM

Double

Ring

Heated

<70° C

CS = Carbon Steel Severe Duty
CM = Carbon Steel MaxLife
CST/AL = Carbon Steel/Aluminum

AL = Aluminum

Содержание E-Flo 333587D















































































































Результаты поиска

Содержание E-Flo 333587D

Отзывы:

Graco E-Flo 333587D, Операция, Страница: 5 / 110

Результаты поиска

Содержание E-Flo 333587D

Отзывы: