Graco E-Flo 333587D Скачать руководство пользователя страница 64

Страница: 64 / 110

Troubleshooting

333587D

V4H_

AMZ

Alarm

High Voltage H_

The incoming

power is above

minimum

acceptable limit

Incoming line to

line voltage has

increased above

265V

For 3 phase with neutral have qualified

electrician verify neutral wire.

V6H_

AMZ

Alarm

Wiring Error H_

The wiring is

invalided from

what the AMZ

is expecting

Wrong wiring of the

power source to

the AMZ

Verify incoming power is wired to the

disconnect correctly per the manual.

WBD_

Driver

Alarm

Encoder

Hardware P_

Encoder or hall

sensor

disconnected

or failed to

commutate

motor

Encoder

disconnected or

faulty

Disconnect pump from AC power. Verify

encoder cable is properly connected. If so,

replace encoder.

WMC_ Driver

Alarm

Control Board P_ Control board

reset due to an

exception in

software

Invalid software

state

Cycle the power to the pump to reset the

driver software.

Software bug

Update software to the latest available on

help.graco.com.

WMH_ Driver

Alarm

Control Board

Off P_

The power to

the control

board has been

turned off

Disconnected

switches

Turn on the disconnected switches.

WMG0 Gateway

Alarm

Gateway Error

Detected

Gateway error

detected;

includes any

error not

covered by a

more specific

error

---

WMN_ Driver

Alarm

Software

Mismatch P_

Software

mismatch

detected in the

motor control

board

Hot board and cold

board have

different software

versions

Update the driver control board software to

the latest available on help.graco.com.

WNG0 Gateway

Alarm

Gateway Map

Error

Missing or

invalid gateway

map

Missing or invalid

gateway map

Install map in gateway.

WSC_

Driver

Deviation

Encoder

Calibration P_

Encoder

calibration

information not

found

Encoder not

calibrated before or

calibration

information deleted

Perform encoder calibration through the

setup screens of the ADM.

WSU0

ADM

Alarm

USB

Configuration

Error

USB

configuration

file not

detected

USB configuration

file not loaded or

was deleted

Update software to the latest available on

help.graco.com.

WSN_

Driver

Alarm

Invalided Styled

Style flow rate

setpoint was

invalided when

trying to run

The style flow rate

setpoint was zero

Place a desired flow rate in the style

definitions page.

Error Location Type

Error Name

Error

Description Cause

Solution

Содержание E-Flo 333587D















































































































Результаты поиска

Содержание E-Flo 333587D

Отзывы:

Graco E-Flo 333587D, Операция, Страница: 64 / 110

Результаты поиска

Содержание E-Flo 333587D

Отзывы: