Goulds Pumps 3700i API610 Скачать руководство пользователя страница 59

Страница: 59 / 126

5.4.2.6 Lubricate the bearings with pure or purge-oil mist (optional)

Before lubricating with purge-oil mist, make sure that the bearing frame is properly lubricated. See Lubri-
cating the bearings.

Prepare the oil-mist generator according to the manufacturer's instructions.

Connect the oil-mist supply lines to the oil ring inspection plug connections. The oil requirements for
ring-oil-lubricated bearings also apply to oil-mist-lubricated bearings.

Connect the drain and vent lines to the outlet connections.

Oil mist inlet

Oil mist outlet

Figure 35: Oil mist lubrication

For pure-oil mist, connect the drain lines to the outlet connections.
This is not required for purge-oil mist.

5.4.2.7 Convert to oil-mist lubrication

NOTICE:

Make sure that pipe threads are clean and apply thread sealant to plugs and fittings.

NOTICE:

For pure oil mist remove pipe plug (408Z and 408I) and install oil mist plugs (843U and 843V).

5.4 Couple the pump and driver

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

Содержание 3700i API610































































































































Результаты поиска

Содержание 3700i API610

Отзывы:

Похожие инструкции для 3700i API610

Бренды по названию

Популярные бренды

Goulds Pumps 3700i API610, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 3700i API610

Отзывы:

Похожие инструкции для 3700i API610

Бренды по названию

Популярные бренды