Rheem Multipak MPE02 Скачать руководство пользователя

Страница: 1 / 60

This water heater must be installed and serviced by a qualified person.

Please leave this guide with a responsible officer.

Owner’s Guide

and

Installation Instructions

Rheem Multipak

Commercial Hot Water Systems

INSTALLER:

The ONLY suitable flue parts are certified Rheem coaxial flue components

carrying the following label:

DO NOT use any other type of flue parts.

Carefully follow the Installation Instructions.

OPERATOR:

DO NOT OPERATE THIS WATER HEATER:

•

Unless a certified Rheem coaxial flue system, venting to the outside through a certified Rheem
terminal, is installed in accordance with the Installation Instructions.

•

If a loud continued vibration occurs during operation

Содержание Multipak MPE02





























































Результаты поиска

Содержание Multipak MPE02

Отзывы:

Похожие инструкции для Multipak MPE02

Бренды по названию

Популярные бренды

Rheem Multipak MPE02, Руководство пользователя и инструкции по установке

Результаты поиска

Содержание Multipak MPE02

Отзывы:

Похожие инструкции для Multipak MPE02

Бренды по названию

Популярные бренды