manualshive.com logo in svg

Rheem Multipak MPE02, Руководство пользователя и инструкции по установке

Поделиться
Скачать
Rheem Multipak MPE02 Скачать руководство пользователя страница 25

INSTALLATION – WATER HEATER 

25 

FLUEING 

 

SECONDARY FLUE 

A secondary flue must be installed with an indoor water heater to discharge combustion products to outside the 
building. The water heater

 

MUST ONLY

 be installed with certified Rheem coaxial flue components carrying the 

label opposite. 

DO NOT

 use any other type of flue parts. 

 

Where more than one water heater is installed, each water heater must 
be individually flued using certified Rheem coaxial flue components. 
 
A common flue system 

MUST NOT

 be used. 

 
The installation of the secondary flue must be carried out by a qualified person and be in accordance with the 
Gas Installations Standard AS/NZS 5601.1, as applicable under local regulations, local authority requirements 
and the installation instructions. A charge will be made for any service related call due to the installation of the 
flue system not complying with these installation instructions. 
 
The water heater must be flued separately from all other appliances and flued to the outdoors. Minimum 
clearance requirements apply from the flue terminal in accordance with AS/NZS 5601.1 (refer also to 

“Flue 

Terminal Location” 

on page 

27

). Do not install the flue to discharge into a chimney. There is no requirement on 

the flue to maintain a minimum distance from combustible materials. 

 

 Warning:

 Where the flue penetrates through walls, floors or ceilings, the penetration must comply with 

local regulations for fire rating. The coaxial flue system does not have nor provides a fire rating. 
 

The water heater flue may be terminated either horizontally with a Horizontal Flue Terminal or vertically with a 
Vertical Flue Terminal. The secondary flue must be self-supporting and not impose a load on the water heater. 
 
Flue runs must be adequately supported along both horizontal and vertical runs. The maximum recommended 
unsupported span for a horizontal run should be no more than 2.0 m. Support isolation hanging bands should 
be used. Do not use wire. Wall Brackets (PN 295129) are available and should be used for vertical runs. The 
coaxial flue components are to be connected together using the screws provided. The flue outside diameter is 
127 mm. 

 

 Warning:

  Never operate the water heater unless it has been installed in accordance with the 

installation instructions. Failure to install the water heater in accordance with the installation 
instructions, properly flueing the water heater to the outdoors and ensuring it has an adequate air 
supply, will result in unsafe operation of the water heater, possibly causing fire, explosion, serious 
injury and asphyxiation from carbon monoxide. 

 
A sealing gasket is located at one end of the inner flue. Check all flue components to ensure the gasket is in 
place and properly seated. 

DO NOT

 install if any gaskets are missing. Contact Rheem Service or their nearest 

Accredited Service Agent if the gasket is missing. 

 

 

 

Содержание Multipak MPE02





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды