manualshive.com logo in svg

Rheem Multipak MPE02, Руководство пользователя и инструкции по установке

Поделиться
Скачать
Rheem Multipak MPE02 Скачать руководство пользователя страница 33

INSTALLATION – WATER HEATER 

33 

HORIZONTAL FLUE INSTALLATION 

 
Horizontal Flueing – Directly Behind Water Heater 

This method of flue installation is used where the secondary flue is to penetrate and terminate immediately 
behind the wall on which the water heater is mounted. 
 
Do not remove the plastic film from the flue outlet of water heater prior to this type of flue installation, to prevent 
debris from the drilling operation entering the water heater flue outlet. 
 

Notes: 

Ensure each flue component is fully engaged and the rubber seal on the inner duct is well seated at each joint. 

Each flue component is supplied with screws to connect to the adjacent flue component. The screws are 
located in a bag taped to the outside of the flue component. 

1. 

Carefully remove the template inserted as the middle pages of this installation instructions booklet. 

2. 

Align the mounting bracket holes on the template exactly over 
the upper wall mounting bracket holes on the water heater. 

This step presumes the water heater is hung on the wall. For floor 
mounted units, align the template as close as possible with the 
upper mounting bracket holes on the water heater. 

 

It may be convenient to tape the template to the wall. 

Note:

  Ensure there are no studs, noggins, pipes or electrical 

cables located in the wall where the flue is to penetrate 

3. 

Mark the pilot hole location through the centre of the template. 

 

Remove but 

DO NOT DISCARD

  the template, repeat for 

each water heater. 

4. 

Drill a pilot hole using a 6.5 mm diameter or smaller drill bit. 

The drill bit must be long enough to penetrate completely through 
the outer skin of the external wall. 

Note:

 Ensure the drill remains level and straight during this step. 

5. 

Cut along the middle of the 

bold

 circle marked “Cut Line” on the template. 

6. 

Align the centre of the template with the pilot hole on the wall surface and scribe around the template onto 
the wall. 

The circle should be 150 mm in diameter. 

 

Remove but 

DO NOT DISCARD

 the template, repeat for each water heater. 

7. 

Align the centre of the template with the pilot hole on the outside wall surface and scribe around the 
template onto the wall. 

The circle should be 150 mm in diameter. 

 

Remove the template. 

8. 

Drill or cut the flue termination hole through the wall using a cutting tool suitable for the wall construction. 

Note:

 The Trim Ring (PN 295125) will cover a 150 mm diameter hole. 

 

 

 

 

Position template 

Содержание Multipak MPE02





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды