Goulds Pumps 3700i API610 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 126

background image

2.

To secure the wear ring (164) locate, drill, and tap three new setscrew holes equally spaced be-
tween the original holes in each new wear ring and wear ring seat area. Install setscrews (222E)
and upset threads.

3.

Confirm the bore diameter of the wear ring (164) after installation.

4.

Check the wear-ring (164) runout and distortion by measuring the bore at each setscrew location
with inside micrometers or vernier calipers. Machine any distortion in excess of 0.08 mm |0.003 in.

6.5.5.1.3 Replace the seal chamber wear ring and throat bushing

1.

Chill a new seal-chamber-cover wear ring (230) and throat bushing (125), using dry ice or another
suitable chilling substance, Install the wear ring into the cover fit and the throat bushing into the seal
chamber fit. Be prepared to tap the wear ring and throat bushing in place with a hardwood block or
soft faced hammer.

2.

To secure the wear ring (230) locate, drill, and tap three new setscrew holes equally spaced be-
tween the original holes in each new wear ring and wear ring seat area. Install setscrews (222E)
and upset threads.

3.

To secure the throat bushing (125) locate, drill, and tap three new setscrew holes equally spaced
between the original holes in each new throat bushing and seal chamber seat area. Install set-
screws (222D) and upset threads.

4.

Confirm the bore diameter of the wear ring (230) after installation.

5.

Check the wear-ring (230) runout and distortion by measuring the bore at each setscrew location
with inside micrometers or vernier calipers. Machine any distortion in excess of 0.08 mm |0.003 in.

222D

222E

125

230

184

184

125

222D

Figure 60: Seal chamber cover wear ring and throat bushing

6.5 Preassembly inspections

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

87

«
...
87
88
89
90
91
...
»

Содержание 3700i API610































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3700i API610

Бренд: Danfoss Страницы: 40

Бренд: Gardena Страницы: 17

Бренд: Jacuzzi Страницы: 8

Бренд: YGHP Страницы: 14

Бренд: IBC Страницы: 22

Бренд: Galmet Страницы: 256

Бренд: EAS Electric Страницы: 165

Бренд: TDRFORCE Страницы: 12

Delta Solo Compact MVP Series

Бренд: KSB Страницы: 40

Бренд: alkitronic Страницы: 12

Бренд: Dantherm Страницы: 17

Бренд: DAB Страницы: 72

EASYDOS Peristaltic V

Бренд: Jesco Страницы: 20

Бренд: Oase Страницы: 42

Бренд: Annovi Reverberi Страницы: 100

Scalekleen EV9796-01

Бренд: Everpure Страницы: 2

Бренд: T.I.P. Страницы: 136

ARO PF20 B Series

Бренд: Ingersoll-Rand Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды