Goulds Pumps 3700i API610 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 126

background image

•

Always keep the work area clean.

•

Pay attention to the risks presented by gas and vapors in the work area.

•

Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash hazards.

•

Always bear in mind the risk of drowning, electrical accidents, and burn injuries.

Safety equipment

Use safety equipment according to the company regulations. Use this safety equipment within the work
area:

•

Hardhat

•

Safety goggles, preferably with side shields

•

Protective shoes

•

Protective gloves

•

Gas mask

•

Hearing protection

•

First-aid kit

•

Safety devices

Electrical connections

Electrical connections must be made by certified electricians in compliance with all international, nation-
al, state, and local regulations. For more information about requirements, see sections dealing specifical-
ly with electrical connections.

Noise

WARNING:

Sound pressure levels may exceed 80 dbA in operating process plants. Clear visual warnings
or other indicators should be available to those entering an area with unsafe noise levels. Per-
sonnel should wear appropriate hearing protection when working on or around any equipment,
including pumps. Consider limiting personnel’s exposure time to noise or, where possible, en-
closing equipment to reduce noise. Local law may provide specific guidance regarding expo-
sure of personnel to noise and when noise exposure reduction is required.

Temperature

WARNING:

Equipment and piping surfaces may exceed 130ºF (54ºC) in operating process plants. Clear
visual warnings or other indicators should alert personnel to surfaces that may reach a poten-
tially unsafe temperature. Do not touch hot surfaces. Allow pumps operating at a high tempera-
ture to cool sufficiently before performing maintenance. If touching a hot surface cannot be
avoided, personnel should wear appropriate gloves, clothing, and other protective gear as nec-
essary. Local law may provide specific guidance regarding exposure of personnel to unsafe
temperatures.

1.2.3.1 Precautions before work

Observe these safety precautions before you work with the product or are in connection with the product:

•

Provide a suitable barrier around the work area, for example, a guard rail.

•

Make sure that all safety guards are in place and secure.

•

Make sure that the equipment is properly insulated when it operates at extreme temperatures.

1.2 Safety

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

7

«
...
7
8
9
10
11
...
»

Содержание 3700i API610































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3700i API610

BURKAY 102 Series

Бренд: A.O. Smith Страницы: 24

HydraPump Smart

Бренд: Watershed Innovations Страницы: 11

JABSCO 11860 Series

Бренд: Xylem Страницы: 24

Бренд: AmeriWater Страницы: 16

American Pride ACNF Series

Бренд: Amana Страницы: 8

Бренд: Metabo Страницы: 77

Бренд: Laars Страницы: 64

Point-of-Use Drinking Water System

Бренд: R-Can Страницы: 12

Бренд: Oase Страницы: 70

Бренд: Beckett Страницы: 2

Бренд: Strom-Electrical Страницы: 8

1 EPBH 9.2-11 T-AVS

Бренд: EBARA Страницы: 16

Бренд: Kelvinator Страницы: 16

KH 4256 AIR PUMP

Бренд: ULTIMATE SPEED Страницы: 72

Бренд: BSC Страницы: 28

Бренд: American Water Heater Страницы: 60

NCE H 25-100/180

Бренд: Calpeda Страницы: 72

CAFS-CP-2 Series

Бренд: Waterous Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды