Gorgy Timing LEDI NETWORK TDS GPS RAIL DIN TH 35 Скачать руководство пользователя

Страница: 98 / 101

MDE-LEDI-NETWORK-TDS-4099V3.0

8.5. SUPERVISION PROTOCOLS

8.5.1. Syslog messages catalogue

The table below shows Syslog messages sent by the device.

Category

Type

Sent text

user (1)

Informational (6)

- A new configuration has been defined.

user (1)

Informational (6)

- A new configuration has been defined through the front panel.

user (1)

Informational (6)

- A new configuration has been defined through the Telnet interface.

user (1)

Informational (6)

- A new configuration has been defined in the \"Alarms\" Webpage.

user (1)

Informational (6)

- A new configuration has been defined in the \"Inputs\" Webpage.

user (1)

Informational (6)

- A new configuration has been defined in the \"Interface\" Webpage.

user (1)

Informational (6)

- A new configuration has been defined in the \"Network\" Webpage.

user (1)

Informational (6)

- A new configuration has been defined in the \"NTP\" Webpage

user (1)

Informational (6)

- A new configuration has been defined in the \"PTP\" Webpage.

user (1)

Informational (6)

- A new configuration has been defined in the \"Output\" Webpage.

user (1)

Informational (6)

- A new configuration has been defined in the \"SNMP\" Webpage.

kern (0)

Informational (6)

- System has restarted, reason: Reset / Power Failure.

kern (0)

Informational (6)

- System has restarted, reason: User Request with Configuration Changes.

kern (0)

Informational (6)

- System has restarted, reason: User Request without Configuration Changes.

kern (0)

Informational (6)

- System has restarted, reason: Automatic for Configuration Changes.

kern (0)

Informational (6)

- System has restarted, reason: Firmware Update.

auth (4)

Informational (6)

- A Web interface has been accessed.

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 4: NTP client software start learning environment&network

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 5: NTP client software entering normal behavior

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 6: Not enough replies of current synchronization server

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 7: New server elected for synchronization

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 8: NTP server software is starting

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 9: The hardware is synchronized on its time reference

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 10: The hardware is not synchronized on its time reference

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 11: NTP server locked by the user

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 13: NTP server software is rescaling on its PPS source

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 14: NTP server software is rescaled on its PPS source

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 15: Failure: no more time code and the time base has no more autonomy

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 16: Warning: no time code. The time base has less than 3 minutes of
autonomy

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 17: The hardware has never been externally synchronized

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 19: Power supply is running again

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 20: Input 1 is no more selectable

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 21: Input 2 is no more selectable

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 22: Input 1 is selectable

daemon (3)

Notice (5)

- A SNMP trap has been sent, with ID 23: Input 2 is selectable

daemon (3)

Error (3)

- An error occurred with the SD-Card.

daemon (3)

Error (3)

- Ethernet link connection.

daemon (3)

Error (3)

- Ethernet link error. Check the cable.

ntp (12)

Error (3)

- NTP Client with MAC address <MAC> from IPvX address <IP> has not requested any synchronization for
<duration> hour(s).

Содержание LEDI NETWORK TDS GPS RAIL DIN TH 35






































































































Результаты поиска

Содержание LEDI NETWORK TDS GPS RAIL DIN TH 35

Отзывы:

Похожие инструкции для LEDI NETWORK TDS GPS RAIL DIN TH 35

Бренды по названию

Популярные бренды

Gorgy Timing LEDI NETWORK TDS GPS RAIL DIN TH 35, Руководство пользователя

Результаты поиска

Содержание LEDI NETWORK TDS GPS RAIL DIN TH 35

Отзывы:

Похожие инструкции для LEDI NETWORK TDS GPS RAIL DIN TH 35

Бренды по названию

Популярные бренды