Gorgy Timing LEDI NETWORK TDS GPS RAIL DIN TH 35 Скачать руководство пользователя

Страница: 84 / 101

MDE-LEDI-NETWORK-TDS-4099V3.0

6.2. DCF-GPS ANTENNA

External dimensions of the casing:

Height: 150mm - Width: 80mm - Depth: 50mm

Ip 54

►

Install away from interference sources such as neon lights, computer scree

ns etc…

6.2.1. DCF Antenna

Part number: 3D6 (4 meters cable included)

Receipt frequency: 77.5 KHz

►

Install the antenna vertically, then rotate it to

get a flashing light at the rhythm of one flash per second
and an extinction every minute (in theory, the antenna has
to be positioned facing the direction of the transmitter
located near Frankfurt in Germany).

☛

The antenna must be placed outside the building

to optimise the radio signal reception.

☛

If the conditions are right, the receiver time

setting requires less than 4 minutes.

☛

In case the time is still not set after fifteen

minutes, it is recommended to look for another location for the antenna.

DCF antenna characteristics

►

Max connection length per shielded two-wire cable: 100 metres

►

Maximum distance from the DCF transmitter (Frankfurt

– Germany) or TDF transmitter

(Allouis

– Cher (France)): 2000km

(Distance may decrease depending on the surrounding terrain and the current atmospheric
conditions)

Содержание LEDI NETWORK TDS GPS RAIL DIN TH 35






































































































Результаты поиска

Содержание LEDI NETWORK TDS GPS RAIL DIN TH 35

Отзывы:

Похожие инструкции для LEDI NETWORK TDS GPS RAIL DIN TH 35

Бренды по названию

Популярные бренды

Gorgy Timing LEDI NETWORK TDS GPS RAIL DIN TH 35, Руководство пользователя

Результаты поиска

Содержание LEDI NETWORK TDS GPS RAIL DIN TH 35

Отзывы:

Похожие инструкции для LEDI NETWORK TDS GPS RAIL DIN TH 35

Бренды по названию

Популярные бренды