GILES FSH-2 Скачать руководство пользователя страница 56

Страница: 56 / 66

Troubleshooting

Model: FSH-2, FSH-2A-99

6-01.

Troubleshooting Procedures - continued

Problem

Probable Cause

Corrective Action

Fryer will not power-up:

•

[HOOD POWER]

light

•

[

FILTER MISSING]

light

•

[FRYER POWER]

light

OFF

a. Baffle filter is missing or not

properly installed

Install filter / check positioning.

b. Charcoal filter is missing or not

properly installed

Install filter / check positioning.

c. Faulty filter switches.

Test & replace as needed.

Fryer will not power-up:

•

[HOOD POWER]

light

•

[

FILTER MISSING]

light

OFFN

•

[FRYER POWER]

light

OFF

• No alarm sounding

a. Fire Suppression system is not

armed.

Contact Ansul service company.

b. Ansul switch is faulty

Contact Ansul service company.

Fryer will not power-up:

•

[HOOD POWER]

light

•

Continuous (steady) tone

alarm

sounding.

•

[FRYER POWER]

light

OFF

a. Baffle or charcoal filter clogged Replace charcoal filter with new •

Clean baffle filter.

b. Hood exhaust outlet excessively

block

Clear of any obstructions.

c. Vacuum switch is out of

adjustment

Test & adjust vacuum switch.

d. Kinked or blocked vacuum line Remove vacuum line kinks or

blockage.

e. Fan running slow or blades are

loaded with grease build-up.

Check voltage and inspect blower;

clean if needed

Fryer will not power-up:

•

[HOOD POWERED]

light

•

[WASH]

light

•

Intermittent (beeping) tone

alarm

sounding.

•

[FRYER POWER]

light

OFF

a. Excessive grease film built up on

collector fins; too dirty

Clean the EAC cell,

Section 4.04.2

b. EAC cell is not installed

Install clean EAC cell.

c. EAC driver board is faulty

Test & replace EAC power supply if

needed.

d. Poor connection at contact

plate; dirty contacts, mis-

alignment, faulty contacts.

Check cell position, clean contacts,

inspect contact plate & replace if

needed.

e. Ionizer wire(s) missing

Replace missing wire(s)

Fryer is ON:

•

[HOOD POWER]

light

•

[CHECK]

light

•

alarm sounding, but cell is

NOT

cleaning air

a. Ionizer wire broken & touching

chassis.

Replace ionizer wire.

b. Collector fins shorted to ground

by moisture.

Dry cell, determine cause of

moisture, cool air being drawn into

hood creating condensation.

Содержание FSH-2



































































Результаты поиска

Содержание FSH-2

Отзывы:

GILES FSH-2, Руководство по эксплуатации и обслуживанию, Страница: 56 / 66

Результаты поиска

Содержание FSH-2

Отзывы: