GForce Ultra Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 89

GForce Ultra Скачать руководство пользователя страница 76

76

•

Check the glycol level.

•

Check glycol concentration to job site requirement.

•

Check water quality to your design requirements and to your local and national codes.

•

Check flow rate.

•

Check water regulating valve and other water components for leaks or damage. Repair as

needed.

•

Check the water Y-strainer. Clean as needed.

9.13. Refrigerant Filter Drier

Factory installed refrigerant filter driers do not normally require maintenance. When replacing
compressors or other repairs that open the refrigeration system to atmosphere, it is advisable to
replace the filter drier. The equivalent type and size should be used.

Check the color code of the moisture indicator on the sight glass. A positive indication means
the filter-drier should be replaced. If the drier is frosted or if there is a perceptible temperature
change between the liquid line entering and leaving the drier, an excessive pressure drop in the
drier is indicated, and the drier should be replaced.

9.14. Electrical Control Enclosure

DANGER:

The inside of the electrical control enclosure contains high

voltage components and wiring. Access should be limited to authorized
personnel.

Arc flash and electric shock hazard. Risk of electrical shock could result in
injury or death. Disconnect local and remote facility power source before
working within this equipment.

Wear appropriate personal protective equipment per NFPA 70E before
working within unit.

Use voltmeter to make sure facility electrical power is turned OFF before
making any electrical connections. Failure to comply can cause injury or
death.

•

Inspect electrical control panel box each year or after a short circuit occurrence.

•

If there is an accumulation of dust and dirt, clean out the panelboard by using a brush,

vacuum cleaner, or clean lint-free rags. Avoid blowing dust into circuit breakers or other
components. Do not use a blower or compressed air.

•

Visually check all conductors and connections to be certain that they are clean and secure.

Loose  and/or  contaminated  connections  increase  electrical  resistance  which  can  cause
overheating.   Such overheating  is indicated by discoloration or flaking of  insulation and/or
metal parts.  Pitting or melting of connecting surfaces is a sign of arcing due to a loose or
otherwise poor connection.  Parts which show evidence of overheating or looseness should
be  replaced  if  damaged.    Tighten  screws  or  bolts  and  nu

ts to component manufacturer’s

torque specifications.

•

Contactors should be kept clean and free from dust and other accumulated deposits. Dust

«
...
74
75
76
77
78
...
»

Содержание Ultra


























































































Отзывы:

Нет отзывов