Getac 9270D Скачать руководство пользователя страница 121

Страница: 121 / 180

4.15 Intel® High Definition Audio Link Signals –Table 1

Name

Type

Description

HDA_RST#

Intel® High Definition Audio Reset:

Master hardware reset

to external codec(s).

HDA_SYNC

Intel High Definition Audio Sync:

48 kHz fixed rate sample

sync to the codec(s). Also used to encode the stream number.

NOTE:

This signal is sampled as a functional strap. See

Section 4.30 for more details.There is a weak integrated pull-
down resistor on this pin.

HDA_BCLK

Intel High Definition Audio Bit Clock Output:

24.000 MHz

serial data clock generated by the Intel High Definition Audio
controller (the Ibex Peak). This signal has a weak internal pull-
down resistor.

HDA_SDO

Intel High Definition Audio Serial Data Out:

Serial TDM

data output to the codec(s). This serial output is double-
pumped for a bit rate of 48 Mb/s for Intel High Definition
Audio.

NOTE:

This signal is sampled as a functional strap. See

Section 4.30 for more details.There is a weak integrated pull-
down resistor on this pin.

HDA_SDIN

[3:0]

Intel High Definition Audio Serial Data In [3:0]:

Serial

TDM data inputs from the codecs. The serial input is single-
pumped for a bit rate of 24 Mb/s for Intel® High Definition
Audio. These signals have integrated pull-down resistors,
which are always enabled.

NOTE:

During enumeration, the Ibex Peak will drive this

signal. During normal operation, the CODEC will drive it.

Содержание 9270D





















































































































































































Результаты поиска

Содержание 9270D

Отзывы:

Похожие инструкции для 9270D

Бренды по названию

Популярные бренды

Getac 9270D, Руководство по обслуживанию

Результаты поиска

Содержание 9270D

Отзывы:

Похожие инструкции для 9270D

Бренды по названию

Популярные бренды