GESTRA NRG 26-60 Скачать руководство пользователя

Страница: 49 / 52

NRG 26-60 - Installation & Operating Manual -

819875-00

Taking out of service

DANGER

Danger to life from scalding caused by escaping hot steam.

Hot steam or water can escape suddenly if level electrodes are unscrewed under pressure.

■

Reduce the boiler pressure to 0 bar and check the pressure before unscrewing the level
electrode.

■

Only remove the level electrode at a boiler pressure of 0 bar.

WARNING

Hot level electrode can cause severe burns.

The level electrode is very hot during operation.

■

Perform installation and maintenance work only on a level electrode that has been allowed
to cool.

■

Only remove level electrodes that have cooled down.

Proceed as follows:

Reduce the boiler pressure to 0 bar.

Allow the level electrode to cool to room temperature.

Switch off the supply voltage.

Unplug the connections of the CAN bus control lines and plug them into one another.

Next, remove the level electrode.

An alarm is triggered when the CAN bus cable is interrupted.

Содержание NRG 26-60





















































Результаты поиска

Содержание NRG 26-60

Отзывы:

Похожие инструкции для NRG 26-60

Бренды по названию

Популярные бренды

GESTRA NRG 26-60, Оригинальное руководство по установке и эксплуатации

Результаты поиска

Содержание NRG 26-60

Отзывы:

Похожие инструкции для NRG 26-60

Бренды по названию

Популярные бренды