Generac Power Systems G007144 Скачать руководство пользователя страница 3

Installation Guidelines For 50 Hz Air-Cooled Generator Sets

iii

Original document - written in English.  

EC Declaration of Conformity 

 

Manufacturer:             

Generac Power Systems, Inc.

 

 

S45 W29290 Hwy 59 
Waukesha, WI 53189 USA 

 

Generac Power Systems, Inc. hereby declares that the machinery described below fulfils all the relevant provisions of the 
Machinery Directive 2006/42/EC. The Machinery also conforms to the relevant provisions of Outdoor Noise Directive 
2000/14/EC (as amended by Directive 2005/88/EC) Notified body: SNCH, 2a, Kalchesbruck L – 1852 Luxembourg, the 
Electromagnetic Compatibility Directive 2014/30/EU, and the Resistance of Hazardous Substances Directive 2011/65/EU 
(as amended by Directive (EU) 2015/863). 

 

 

Machinery Description:

 

Generator Set 

Model Number: 

Generac Model Numbers; G007144#, G007244#, G007145#, G007245#, G007146# and 
G007246#  (“#” – 0 to 9 for minor design changes)  

 

The following standards have been complied with in part or in full as relevant:  

Machinery Directive 2006/42/EC Harmonised Standards applied: 

EN ISO 8528-13:2016 - Reciprocating internal combustion engine driven alternating current generating sets 
IEC 60204-1:2010/AC:2010 - Electrical equipment of machines - Part 1:  General requirements 
ISO 12100:2010 - General principles for design -  Risk Assessment and risk reduction, includes EN 14121:2007                       

Additional standards that have either been referred to or been complied with in part or in full as relevant: 

ISO 8528-1:2005 - Reciprocating internal combustion engine driven alternating current generating sets 
ISO 8528-5:2013 - Reciprocating internal combustion engine driven alternating current generating sets 
IEC 60034-1:2010 - Rotating electrical machines – Part 1: Rating and performance 

 

Harmonised Standards applied for Outdoor Noise Emission Directive 2000/14/EC: 

ISO 8528-10:1998 – Reciprocating internal combustion engine driven alternating current generating sets 

EN ISO 3744:2010 - 

Determination of sound power levels and sound energy levels of noise sources using sound pressure 

Model number G007144# & G007244#: measured sound power level 94.0 dB(A), guaranteed sound power level 95 dB(A) 
Model number G007145# & G007245#: measured sound power level 94.2 dB(A), guaranteed sound power level 95 dB(A) 
Model number G007146# & G007246#: measured sound power level 94.8 dB(A), guaranteed sound power level 96 dB(A) 

 

Harmonised Standards applied for Electromagnetic Compatibility Directive 2014/30/EU: 

EN 55012:2007+A1:2009 – Vehicles, boats and internal combustion engines – Radio disturbance characteristics 
EN 55014-1:2006 – Electromagnetic Compatibility – Requirements for household appliances, electric tools and similar 

apparatus. Part 1 - Emission 

EN 55014-2:2015 – Electromagnetic compatibility – Requirements for household appliances, electric tools and similar 

apparatus. Part 2 - Immunity 

EN 61000-3-2:2014 - Electromagnetic compatibility – Part 3-2: Limits – Limits for harmonic current emissions 
EN 61000-3-3:2013 - Electromagnetic compatibility – Part 3-3: Limits – Limitation of voltage changes, voltage fluctuations 

and flicker in public low-voltage supply systems. 

 

Harmonised Standards applied for Restriction of Hazardous Substances Directive 2011/65/EC: 

IEC 63000:2016 – Technical documentation for the assessment of electrical and electronic products 

 

A Technical file has been compiled in accordance with Part A of Annex VII of Machinery Directive 2006/42/EC and is available 
to the European National authorities upon request. 
 

Jeffrey Jonas 

Signature:  

Sr. Staff Engineer-Global Product Compliance 
Generac Power Systems, Inc. 
S45 W29290 Hwy 59 
Waukesha, Wisconsin, USA 

 

This document was made at Generac Power Systems, Inc. at the address noted above on October 14, 2020 

Содержание G007144





































































Отзывы: