Generac Mobile MGG450 Скачать руководство пользователя страница 3

Страница: 3 / 60

Table of Contents

Owner’s Manual for MGG450

iii

Introduction .......................................................1

Read This Manual Thoroughly ..........................1
How to Obtain Service ......................................1

Safety Rules ......................................................1
General Hazards  ...............................................2
Explosion and Fire Hazards  ..............................2
Trailer Hazards ..................................................2
Electrical Hazards  .............................................3
Battery Hazards  ................................................3

General Information

Component Locations  .......................................5
Specifications  ....................................................6
Emissions Information .......................................7
Unit and Serial Number Locations  ....................7
Digital Controller ................................................7
Cold Weather Starting Aids (Shore Power) .......7
Control Panel  ....................................................8

Fuel Selection Screen  .......................................8
Engine Knock Intensity Screen  .........................9
Ignition Secondary Voltage Display Screen  ......9
Setting the Controller Date and Time ................9

Dual Fuel System ..............................................9

Natural Gas (Well Gas) Fuel System ..............11
LP Liquid Withdrawal Fuel System .................11

Generator Features .........................................11
Generator and Load Compatibility  ..................11
Engine/Generator Protective Devices  .............11
Containment Pan  ............................................11
Battery Disconnect Switch  ..............................11
Lifting the Unit  .................................................12

Single Point Lift ...............................................12
Four Point Lift ..................................................12
Fork Pockets ...................................................12

Operation

Generator Set Up ............................................13

Well Site Approval ...........................................13
Natural Gas Connections ................................13
LP Liquid Connections (Liquid Withdrawal Sys-
tem) .................................................................14

Fuel Scrubbing System ...................................15

System Set Up ................................................15
Electrical Connections .....................................15

Prestart Checklist ............................................15
Starting the Generator .....................................16

Automatic Fuel Switching ................................16

Natural Gas Only Operation ............................16
Non-Commercial (Well Gas) Only Operation ..16
LP Liquid Only Operation ................................17
Gaseous and LP Liquid (Automatic mode) Oper-
ation ................................................................17
50 Hz Operation ..............................................17

Operation Checks  ...........................................17
Overcrank Shutdown  ......................................18
Emergency Stop Switch ..................................18
Engine Oil Replenishment System  .................18
Generator Output Connections .......................18
Customer Convenience Receptacles  .............19
Main Circuit Breaker  .......................................19
Circuit Breaker Box .........................................19

Frame Ground Connection .............................19

Paralleling Startup ..........................................20

Parallel MGG450 to Another MGG Genset .....20
Parallel MGG450 to Other Gensets ................20

Paralleling Shutdown  ......................................20
General Wiring Considerations .......................21
Derating  ..........................................................21
Towing the Trailer  ...........................................22
Trailer Wheel Bearings  ...................................22

Maintenance

Disabling Generator for Maintenance .............23
Maintenance ...................................................23

Basic Maintenance Schedule ..........................24
Daily Walk Around Inspection  .........................24
Engine Oil Recommendations  ........................24
Check Engine Oil Level ...................................25
Changing the Oil  .............................................25
Coolant Recommendation  ..............................25
Adding Coolant  ...............................................26
Resetting Service Timers ................................26

Battery Inspection ...........................................26

Battery Installation and Replacement .............27

Other Maintenance Checks ............................27
Jack Maintenance ...........................................27

Side-Wind Models ...........................................27
Top-Wind Models ............................................28

Trailer Wheel Bearings ...................................28
Fuel Scrubbing System ...................................28

Operation  ........................................................28
Pressure Settings ............................................29
Automatic Filtration  .........................................29
Replacing the Filter  .........................................29

Air Filter Drain Inspection ...............................29

Содержание MGG450





























































Результаты поиска

Содержание MGG450

Отзывы:

Похожие инструкции для MGG450

Бренды по названию

Популярные бренды

Generac Mobile MGG450, Руководство пользователя

Результаты поиска

Содержание MGG450

Отзывы:

Похожие инструкции для MGG450

Бренды по названию

Популярные бренды