manualshive.com logo in svg

Generac Mobile MGG450, Руководство пользователя

Скачайте бесплатно руководство для владельца Generac Mobile MGG450 на manualshive.com. Этот мануал поможет вам легко использовать и обслуживать ваш генератор. Получите детальные инструкции по эксплуатации, техническому обслуживанию и безопасности для оптимальной производительности вашего оборудования.

Поделиться
Скачать
background image

40

Owner’s Manual for MGG450

Troubleshooting

Alarm

Definition

BOC IDMT

Indicates current IDMT protection activation. Current IDMT protection is 
inverse definite minimum time protection which is based on the generator 
current. Protection reaction time depends on overcurrent value. High over-
current means short reaction time whereas low overcurrent means longer 
reaction time. Protection is based on setpoints Generator protect: 2Inom 
del and Basic settings: Nomin current.

MPR Imains IDMT

Indicates current IDMT protection activation. Current IDMT protection is 
inverse definite minimum time protection which is based on the mains cur-
rent. Protection reaction time depends on overcurrent value. High overcur-
rent means short reaction time whereas low overcurrent means longer 
reaction time.
This protection is active if the Mns2Inom prot setpoint is set to ENABLED. 
Protection is based on setpoints Mains protect: Mains2Inom del and Basic 
settings: Nomin current.

BOR IbusL IDMT

Indicates current IDMT protection activation. Current IDMT protection is 
inverse definite minimum time protection which is based on the left bus 
current. Protection reaction time depends on overcurrent value. High over-
current means short reaction time whereas low overcurrent means longer 
reaction time.
This protection is active if the BusL2Inom prot setpoint is set to ENABLED. 
Protection is based on setpoints BusL protect: BusL2Inom del and Basic 
settings: Nomin current.

BOC ShortCurr

Generator short current protection was activated. Generator current was 
over Generator protect: Ishort level for Ishort del. time.

BOC Overload

Indicates overload IDMT protection activation. Overload IDMT protection 
is inverse definite minimum time protection which is based on the genera-
tor power. Protection reaction time depends on generator power value. 
High generator overload means short reaction time whereas low generator 
overload means longer reaction time. Protection is based on setpoints 
Generator protect: OverldStrtEval and 2POverldStEvDel.

MPR Pmains IDMT

Indicates overload IDMT protection activation. Overload IDMT protection 
is inverse definite minimum time protection which is based on the mains 
power. Protection reaction time depends on mains power value. High 
mains overload means short reaction time whereas low mains overload 
means longer reaction time.
This protection is active if the Mns2POvrldProt setpoint is set to 
ENABLED. Protection is based on setpoints Mains protect: OverldStrtEval 
and 2POverldStEvDel.

BOR PbusL IDMT

Indicates overload IDMT protection activation. Overload IDMT protection 
is inverse definite minimum time protection which is based on the left bus 
power. Protection reaction time depends on the left bus power value. High 
left bus overload means short reaction time whereas low left bus overload 
means longer reaction time.
This protection is active if the BusL2POvrldProt setpoint is set to 
ENABLED. Protection is based on setpoints BusL protect: OverldStrtEval 
and 2POverldStEvDel.

BOC NCB fail

NCB fail is detected if the NeutralCB fdb input doesn't follow Neutral CB C/
O output
within 400 ms.

Wrn BadPwrCfg

Power format is set differently in controllers which are part of the same 
control group. Check Power formats setting in GenConfig on the Miscella-
neous card (available in the Advanced mode only).

Содержание MGG450





























































Отзывы:

Нет отзывов

Похожие инструкции для MGG450

Balmar 60 Series Installation And Operation Manual preview
60 Series
Бренд: Balmar Страницы: 20
Icar MICROfix Installation And Operation Manual preview
MICROfix
Бренд: Icar Страницы: 2
Westinghouse Gen9500DF User Manual preview
Gen9500DF
Бренд: Westinghouse Страницы: 100
VOLTCRAFT PS-1305-230 Operating Instructions Manual preview
PS-1305-230
Бренд: VOLTCRAFT Страницы: 50
Baofeng GM-5RS User Manual preview
GM-5RS
Бренд: Baofeng Страницы: 34
Akai AWS08BK Manual preview
AWS08BK
Бренд: Akai Страницы: 2
Coby TF-DVD1021 Specifications preview
TF-DVD1021
Бренд: Coby Страницы: 1
Avtech AVRQ-5-B Instructions Manual preview
AVRQ-5-B
Бренд: Avtech Страницы: 91
Hytera X1e Owner'S Manual preview
X1e
Бренд: Hytera Страницы: 18
Pace IntelliHeat ST 115 Operation And Maintenance Manual preview
IntelliHeat ST 115
Бренд: Pace Страницы: 20
LG DP-1300 Manual preview
DP-1300
Бренд: LG Страницы: 14
LG DP-9821 Owner'S Manual preview
DP-9821
Бренд: LG Страницы: 45
LG DP-482B Manual preview
DP-482B
Бренд: LG Страницы: 17
LG DP-375R Manual preview
DP-375R
Бренд: LG Страницы: 19
LG DP-582B Owner'S Manual preview
DP-582B
Бренд: LG Страницы: 24
LG DP-471B Manual preview
DP-471B
Бренд: LG Страницы: 16
LG DP-472B Manual preview
DP-472B
Бренд: LG Страницы: 34
LG DP170N Owner'S Manual preview
DP170N
Бренд: LG Страницы: 37

Бренды по названию

Популярные бренды

Загрузить еще бренды