Generac Mobile MGG450 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 60

background image

30

Owner’s Manual for MGG450

Maintenance

Operation

If the unit is not operating and the temperature is below
60 °F (16 °C) ambient, shore power operates a 500 watt
resistive heater inside the fuel conditioning enclosure, a
6.0 kW integrated coolant pump/heater activates, and a
submersed resistive oil pan heater activates. The devices
activate independently of one another.
If the unit is operating and the temperature is below 60 °F
(16 °C) ambient, generator power operates a blower to
move air across the exterior of the exhaust manifold into
the fuel conditioning enclosure.

NOTE:

Block heater and oil pan heaters are not active

while operating.

While installed, the variable-pitch fan automatically varies
the pitch of the blades to maintain optimal airflow based
on coolant temperature and intake manifold temperature.
This  operation  will  inherently  minimize  fan  power
required and lower overall fuel consumption during cooler
ambient operating temperatures.
If  a  cooling  system  blockage  occurs  from  reverse  flow
operation  (snow,  ice,  leaves,  etc.),  high  coolant  and/or
intake manifold temperatures will force the fan back into
forward flow operation. If the blockage is cleared the fan
will return to reverse flow operation once the coolant and
intake  manifold  temperatures  return  to  normal.  If  the
blockage is not cleared with the change to forward flow
the unit may shutdown due to high coolant temperature
and/or intake manifold temperature.

Battery

Warmer

Throttle

Intake

Manifold

ENGINE

Exhaust

Manifold

Oil Sump

Turbo

Wellhead Gas
Max Inlet
Pressure-
300psi

Regulator Fuel

Strainer

Regulator

Zero

Governor

Mixer

Gas / Liquid
Separator

Coalescing
Filter

Liquid propane

Vaporizers

Fuel Safety

Valves

Fuel Safety

Valves

Crankcase

Breather Line

Breather Line

e

Resistive

Heater

Block Heater

SHORE

POWER

SYSTEM

Battery

Warmer

Throttle

Intake

Manifold

ENGINE

Exhaust

Manifold

Oil Sump

Turbo

Wellhead Gas
Max Inlet
Pressure-
300psi

Regulator Fuel

Strainer

Regulator

Zero

Governor

Mixer

Gas / Liquid
Separator

Coalescing
Filter

Liquid propane

Vaporizers

Fuel Safety

Valves

Fuel Safety

Valves

Crankcase

Breather Line

Breather Line

e

Resistive

Heater

Block Heater

SHORE

POWER

SYSTEM

Unit Not Operating

Ambient Below 60 degF

Unit Operating

Ambient Below 60 degF

Radiator

and CAC

Radiator

and CAC

AUTO

FAN

AUTO

FAN

001729

Figure 4-3. Variable Pitch Automatic Fan

«
...
32
33
34
35
36
...
»

Содержание MGG450





























































Отзывы:

Нет отзывов

Похожие инструкции для MGG450

Бренд: Mag One Страницы: 8

Бренд: Kimo Страницы: 20

Invertron 4500L-3P-4728

Бренд: California Instruments Страницы: 6

Бренд: AudioSonic Страницы: 45

Бренд: Icar Страницы: 2

20KW Home Generator System

Бренд: Briggs & Stratton Страницы: 22

Бренд: Briggs & Stratton Страницы: 5

Бренд: GENMAX Страницы: 8

Бренд: Baofeng Страницы: 25

Бренд: AWA Страницы: 25

Бренд: Schulz Страницы: 64

TETRA Release 2

Бренд: Rohde & Schwarz Страницы: 81

Бренд: Rohde & Schwarz Страницы: 80

Super Slim Portable Stereo Speaker

Бренд: Jumbl Страницы: 1

Бренд: BK Radio Страницы: 37

Бренд: DUROMAX Страницы: 68

Бренд: DUROMAX Страницы: 82

Бренд: DUROMAX Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды