Generac Mobile MGG450 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 60

background image

Owner’s Manual for MGG450

3

Introduction and Safety

Electrical Hazards

(000145)

DANGER

Electrocution. In the event of electrical accident,
immediately shut power OFF. Use non-conductive
implements to free victim from live conductor. Apply
first aid and get medical help. Failure to do so will
result in death or serious injury

.

(000104)

DANGER

Electrocution. Water contact with a power
source, if not avoided, will result in death
or serious injury.

(000144)

DANGER

Electrocution. Contact with bare wires,
terminals, and connections while generator
is running will result in death or serious injury.

(000152)

DANGER

Electrocution. Verify electrical system is
properly grounded before applying power.
Failure to do so will result in death or serious
injury.

(000123)

DANGER

Electrocution. Turn utility supply OFF before
working on utility connections of the transfer
switch. Failure to do so will result in death or
serious injury.

(000150)

DANGER

Electrocution. Never connect this unit to the electrical
system of any building unless a licensed electrician
has installed an approved transfer switch. Failure to
do so will result in death or serious injury.

Battery Hazards

(000188)

DANGER

Electrocution. Do not wear jewelry while
working on this equipment. Doing so will
result in death or serious injury.

(000137a)

WARNING

Explosion. Batteries emit explosive gases while
charging. Keep fire and spark away. Wear protective
gear when working with batteries. Failure to do so
could result in death or serious injury.

(000162)

WARNING

Explosion. Do not dispose of batteries in a fire.
Batteries are explosive. Electrolyte solution can cause
burns and blindness. If electrolyte contacts skin or eyes,
flush with water and seek immediate medical attention.

(000163a)

WARNING

Risk of burn. Do not open or mutilate batteries.
Batteries contain electrolyte solution which can
cause burns and blindness. If electrolyte contacts
skin or eyes, flush with water and seek immediate
medical attention.

WARNING

(000228)

Environmental Hazard. Always recycle batteries at an
official recycling center in accordance with all local
laws and regulations. Failure to do so could result in
environmental damage, death, or serious injury.

Always  recycle  batteries  in  accordance  with  local  laws
and regulations. Contact your local solid waste collection
site  or  recycling  facility  to  obtain  information  on  local
recycling  processes.  For  more  information  on  battery
recycling,  visit  the  Battery  Council  International  website
at:

http://batterycouncil.org

«
...
5
6
7
8
9
...
»

Содержание MGG450





























































Отзывы:

Нет отзывов

Похожие инструкции для MGG450

Бренд: JBL Страницы: 11

Бренд: Samsung Страницы: 131

Бренд: BAUKER Страницы: 43

Бренд: Agilent Technologies Страницы: 126

Бренд: Naxa Страницы: 4

Бренд: V-Zon Страницы: 26

Бренд: Pyle Страницы: 4

Бренд: Champion Power Equipment Страницы: 29

Бренд: Denyo Страницы: 90

Бренд: LoadUP Страницы: 60

Бренд: Sportsman Страницы: 30

Бренд: Star Cool Страницы: 224

Бренд: Pecron Страницы: 12

Бренд: Pecron Страницы: 16

Бренд: Guardian Страницы: 4

Бренд: Guardian Страницы: 22

Бренд: Sunstech Страницы: 22

Бренд: Buffalo Tools Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды