Generac Mobile MGG450 Скачать руководство пользователя страница 10

Страница: 10 / 60

Owner’s Manual for MGG450

General Information

Specifications

Description

Units

60 Hz

50 Hz

Engine

hp (kW)

465 (347)

hp (kW)

558 (416)

rpm

1800

1500

(L)

1336.42 (21.9)

/hr (m

/hr)

4563 (129.2)

/hr (m

/hr)

3992 (113.1)

/hr (m

/hr)

4374 (124.0)

/hr (m

/hr)

4374 (124.0)

Generator

kW (kVA)

360 (450)

288 (360)

kW (kVA)

300 (375)

240 (300)

Ampere

541

520

Ampere

451

433

—

Class H rated

—

Class H rated

AC Distribution

Ampere

600

Volt

277 / 480

231 / 400

Battery

Battery Type—Group Number

—

Battery Voltage

system voltage

(quantity per unit)

12V (2)

Battery Rating

amp-hours (CCA)

225 (1,100)

Weights

lbs (kg)

12,110 (5493)

lbs (kg)

15,281 (6931)

Dimensions

in (m)

204 x 72 x 101 (5.18 x 1.83 x 2.57)

in (m)

253 x 102 x 131 (6.43 x 2.59 x 3.33)

Capacities

gal (L)

92 (87)

gal (L)

38 (144)

Trailer

—

3 in lunette ring

psi (kPA)

105 (724)

Specifications are subject to change without notice. Refer to the product specification sheet for complete list.

Rated Engine Power Output—Continuous

Rated Engine Power Output—Prime

Operating Speed

Displacement

Fuel Consumption NG—100% Prime

Fuel Consumption NG—100% Continuous

Fuel Consumption LP—100% Prime

Fuel Consumption LP—100% Continuous

Power Output 3Ø Prime

Power Output 3Ø Continuous

Power Output 3Ø Prime

Power Output 3Ø Continuous

Rotor Insulation

Stator Insulation

Circuit Breaker Size

Available Voltage—Three-Phase

Operating Weight—Skid Mounted

Operating Weight—Trailer Mounted

Skid Mounted (L x W x H)

Trailer Mounted (L x W x H)

Coolant (including engine)

Oil (including filter and reservoir tank)

Hitch

Maximum Tire Pressure

Содержание MGG450





























































Результаты поиска

Содержание MGG450

Отзывы:

Похожие инструкции для MGG450

Бренды по названию

Популярные бренды

Generac Mobile MGG450, Руководство пользователя

Результаты поиска

Содержание MGG450

Отзывы:

Похожие инструкции для MGG450

Бренды по названию

Популярные бренды