Gehl CTL60 Скачать руководство пользователя страница 164

Страница: 164 / 170

162

INDEX

Accessories ................................................................ 52

After Cold Weather is Over ........................................ 79

After First 50 Hours (New Machines Only) ............. 107

After First 500 Hours (New Machines Only) ............ 116

After starting the engine ............................................. 15

After the Fuel Runs Out ........................................... 137

Always clean the machine ......................................... 26

Always keep the machine clean ................................. 12

Anti-explosive lighting ................................................ 25

Attach a “DO NOT OPERATE” tag ............................ 25

Auxiliary Hydraulic Lines ............................................ 55

Auxiliary Hydraulic Switches ...................................... 49

Auxiliary Pedal (If equipped) ...................................... 53

Avoid battery hazards ................................................ 30

Avoid fire and explosion hazards ............................... 10

Avoid overloading and off-center loads ...................... 20

Be careful not to get crushed or cut ........................... 11

Be careful with fluids under pressure ......................... 29

Be careful with grease under pressure ...................... 29

Be careful with hot and pressurized components ........... 28

Be careful with hot cooling systems ........................... 29

Before Starting Operation .......................................... 60

Before Starting the Engine ......................................... 61

Bleeding the Air from the Fuel System ..................... 137

Caution against the falling of an unstable load .......... 19

Cautions ..................................................................... 81

Cautions after Completing Operations ....................... 79

Cautions on Maintenance .......................................... 88

Cautions on Operating ............................................... 72

Cautions on tilting up the canopy ............................... 27

Cautions on Towing .................................................... 22

Cautions on Transporting ........................................... 86

Cautions on traveling and turning .............................. 17

Cautions on traveling on slopes ................................. 18

Cautions on Traveling on Slopes ............................... 74

Check for safety in the surrounding area before

starting ................................................................... 16

Check the strength of the bridge ................................ 12

Checks after maintenance ......................................... 31

Cleaning the Engine Cooling System ...................... 120

Cleaning the Radiator and Oil Cooler Fins .............. 117

Cleaning the Water Separator (CTL 60 / CTL80) ..... 114

Clear the area of other persons before starting the

machine ................................................................. 14

Controls ...................................................................... 35

Crush Hazard FOPS Limitations .................................. 9

Daily Inspection .......................................................... 58

Daily Inspection (Every 10 Hours) ........................... 102

Danger of flying objects ............................................. 22

Disconnect the battery ............................................... 30

Disposing of wastes ................................................... 31

Do not allow unauthorized personnel in the work

area ........................................................................ 25

Do not carry the bucket over the heads of people ........... 19

Do not drive into materials at high speed ................... 19

Do not enter soft ground ............................................ 21

Do not permit riders on the machine .......................... 16

Do not suddenly stop or lower the working

equipment .............................................................. 20

Doors and Covers ...................................................... 38

Draining the Fuel Tank ............................................. 113

A ~ D

Содержание CTL60











































































































































































Результаты поиска

Содержание CTL60

Отзывы:

Gehl CTL60, Руководство оператора, Страница: 164 / 170

Результаты поиска

Содержание CTL60

Отзывы: