Gehl CTL60 Скачать руководство пользователя страница 118

Страница: 118 / 170

116

MAINTENANCE

After First 500 Hours (New Machines Only)

Replacing the Travel Motor Gear Oil

WARNING

Stop the engine and allow the machine
to cool down before performing
maintenance.
• The travel motors are hot directly

after the engine is stopped. Touching
them will cause burns.

• The gear oil is also hot and under

high pressure.
Be careful when loosening plugs.
Working on the machine under these
conditions could result in burns or
injuries.

The pressure in the travel motor
reduction gears case may cause oil or
the plug to fly out. Loosen the plug
slowly to release the pressure.

IMPORTANT: If the percentage of the
traveling time within the total operating
time is high, replace the gear oil earlier
than the specified time.

1. Set the travel motor so that plug (1) is at

the very bottom.

2. Place a pan for catching the spent oil

under plug (1).

3. Remove plugs (1), (2) and (3) and drain

the oil.

4. Wrap new sealing tape around the plugs.
5. Tighten plug (1).
6. Supply oil through the hole for plug (3) until

oil flows out of the hole of plug (2).

7. Tighten plugs (2) and (3).

T7G018

OIL.L.

Содержание CTL60











































































































































































Результаты поиска

Содержание CTL60

Отзывы:

Gehl CTL60, Руководство оператора, Страница: 118 / 170

Результаты поиска

Содержание CTL60

Отзывы: