Gehl CTL60 Скачать руководство пользователя страница 46

Страница: 46 / 170

CONTROLS

Instrument Panel

Warning Lamps

IMPORTANT: If a warning lamp flashes
and an alarm is sounded, stop all
operations immediately and inspect and
maintain the appropriate part.

Refer to page 140 “Troubleshooting”.

1. Engine Emergency Lamp

This lamp flashes and an
alarm is sounded if the
engine oil pressure or
coolant level in the radiator

drops or the coolant temperature rises
abnormally while the engine is running. After
approximately 5 seconds, the engine stops
automatically.

2. Engine Oil Pressure/Coolant Level

Warning Lamp

This lamp flashes and an
alarm is sounded if the
lubricant oil pressure or
coolant level in the radiator

drops abnormally while the engine is running.

3. Coolant Temperature Warning Lamp

This lamp flashes and an
alarm is sounded if the
engine coolant temperature
rises abnormally while the

engine is running.

4. Battery Charge Warning Lamp

This lamp flashes and an
alarm is sounded if a
problem arises in the
charging system while the

engine is running.

5. Air Cleaner Warning Lamp

This lamp flashes and an
alarm is sounded if the air
cleaner filter is clogged while
the engine is running.

6. Line Filter Warning Lamp

This lamp flashes and an
alarm is sounded if the
hydraulic oil line filter is
clogged while the engine is

running. This lamp may flashes directly after
the engine in started in cold weather. This is
not a malfunction. The lamp will turn off while
the engine is warming up.

T7B007

L3B036

C4B012

G4B010

T7B008

T7B0061

C4B030

Содержание CTL60











































































































































































Результаты поиска

Содержание CTL60

Отзывы:

Gehl CTL60, Руководство оператора, Страница: 46 / 170

Результаты поиска

Содержание CTL60

Отзывы: