Gehl CTL60 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 170

Gehl CTL60 Скачать руководство пользователя страница 142

140

TROUBLESHOOTING

If a Warning Lamp Flashes

If an alarm is sounded or a warning lamp starts flashing during operation, park the machine
in a safe place and perform the procedures described below.

Warning lamp

Lamp name

Procedure

Engine
emergency
lamp

Engine oil
pressure/
coolant level
warning
lamp

Coolant
temperature
warning
lamp

Battery
charge
warning
lamp

Air cleaner
warning
lamp

A problem has occurred in the engine lubrication system
or the coolant water temperature has risen irregularly.

¡

When there is a problem in the engine lubrication
system or coolant level, the engine oil pressure/
coolant level warning lamp flashes simultaneously.

¡

When the coolant temperature has risen irregularly,
the coolant temperature warning lamp flashes
simultaneously.

For the procedures, refer to the respective warning
lamps below.

Inspect the engine oil level or coolant level. If the lamp is
flashing even though the level is normal or if it continues
flashing after oil or coolant are added, consult a Gehl
sales or service outlet.
Refer to page 102 or 103 “Inspecting and replenishing the
coolant” or “Inspecting and Replenishing the Engine Oil”.

The coolant temperature has risen irregularly and the
engine is overheating.
Refer to page 135 “If the Engine Overheats”.

There is a problem with the fan belt or charger. Inspect
the fan belt for slack or breakage and adjust as
necessary. If the lamp continues flashing after
maintenance, there is a problem with the charger.
Consult a Gehl sales or service outlet.
Refer to page 109 “Inspecting and Adjusting the Fan
Belt”.

The air cleaner filter is clogged.

OSOB080

C4B012

G4B010

L3J004

T7B007

C

«
...
140
141
142
143
144
...
»

Содержание CTL60











































































































































































Отзывы:

Нет отзывов