Gehl CTL60 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 170

Gehl CTL60 Скачать руководство пользователя страница 92

90

MAINTENANCE

Service Data

Fuel and Lubricant Chart

Use different fuels, lubricants and greases according to the temperature, referring to the
chart below.

¡

Change the lubricant earlier than as shown in the table if it is extremely dirty or its
performance has deteriorated severely.

¡

Whenever possible, use the same brand of lubricant as before. If changing with a different
brand, replace the entire quantity – do not mix different brands.

Part

Type

Replacement
interval

Capacity

Lit. (US. qt.)

Type by temperature

-22 -4 14 32 50 68 86 104

°

F

-30 -20 -10 0

10 20 30 40

°

C

Engine
oil pan

Diesel
engine oil
API-CD

After first 50
hrs.
Every 250 hrs.

Hydraulic
tank

Fuel tank

Engine
cooling
system

Travel
reduction
gear

Working
equipment

Diesel fuel

Coolant
(water**+
coolant***)

Gear oil
API-GL-4

Lithium
based
grease
EP-2
NLGI No.2

Every 1000 hrs.

Every 1000 hrs.

Daily or every
10 hrs.

When required

After first 500
hrs.*
Every 1000 hrs.

As required

SAE 90

Use a clean, Quality fuel for good performance and optimum engine life.

• To prevent fuel flow problems in cold weather, use diesel fuel with a pour point of

at least -12

°

C (10

°

F) below the lowest expected ambient temperature.

• Minimum cetane number is 45. Low temperature or high altitude operation may

require the use of fuel with a higher cetane number.

Diesel
engine oil
API-CD

Levers and
Pedal

CTL60:1.1(1.16)
CTL70:1.1(1.16)
CTL80:1.8(1.9)

CTL60:10.9(11.5)
CTL70:15(15.9)
CTL80:15(15.9)

CTL60:75
(19.8 US.gal.)
CTL70:90
(23.8 US.gal.)
CTL80:108
(28.5 US.gal.)

System
CTL60:60
(15.9 US.gal.)
CTL70:83
(21.9 US.gal.)
CTL80:95
(25.1 US.gal.)

Tank
CTL60:39
(10.2 US.gal.)
CTL70:52
(13.7 US.gal.)
CTL80:64
(16.9 US.gal.)

Upper limit
CTL60:10.2(10.8)
CTL70:9.6(10.1)
CTL80:14(14.8)

Lower limit
CTL60:5.7(6.0)
CTL70:7.6(8.0)
CTL80:7(7.4)

SAE 10W-30

SAE 5W-20

SAE 10W-30

SAE 15W-40

30% coolant mixture

50% coolant mixture

«
...
90
91
92
93
94
...
»

Содержание CTL60











































































































































































Отзывы:

Нет отзывов