Gehl CTL60 Скачать руководство пользователя страница 15

Страница: 15 / 170

SAFETY

Preparing Precautions

Perform inspection and
maintenance daily

Failure to notice or repair machine
irregularities or damage can lead to
accidents.

Before operating, perform the prescribed
inspections and make repairs immediately
should any irregularities be found.

If a failure that causes loss of control such
as steering, service brakes or engine
occurs, stop the machine motion as
quickly as possible, follow the shutdown
procedure, and keep machine securely
parked until the malfunction is corrected.

Emergency Exit

If you should become trapped inside the cab,
remove the rear window to get out.

There are two ways to remove the rear
window.

In case of emergency
1. Kick off the rear window. Note that the

glass may break. Be careful not to get
injured.

In case of need
1. Pull off ring (A) and remove the tip of the

rubber wedge.

2. Grasp the tip, pull, and remove the entire

rubber wedge.

3. Pull inside knob (B).

E X I T

T8B001

Содержание CTL60











































































































































































Результаты поиска

Содержание CTL60

Отзывы:

Gehl CTL60, Руководство оператора, Страница: 15 / 170

Результаты поиска

Содержание CTL60

Отзывы: