Gehl CTL60 Скачать руководство пользователя страница 120

Страница: 120 / 170

118

MAINTENANCE

6. Install the new filter by hand.
7. Tighten 2/3 more turn with the filter wrench

after the filter packing comes in contact
with the surface of installation.

8. Bleed the air.

Refer to page 137 “Bleeding the Air from
the Fuel System”.

Replacing the Feed Pump Filter
(CTL70)

WARNING

Do not smoke or permit open flames
while handling fuel or working on the
fuel system.

Stop the engine in a well-ventilated
place and allow it to cool down before
performing maintenance.

Clean up spilled fuel immediately.

1. Open the rear door.
2. Remove the bolts (a) and open the radiator

(b).

3. Place a pan under the feed pump (1).
4. Remove the cover (2).
5. Remove the element (3) and gaskets (4).
6. Install the new element and gaskets.
7. Tighten the cover (2).

Every 500 Hours

T9G006

T9G0071

Содержание CTL60











































































































































































Результаты поиска

Содержание CTL60

Отзывы:

Gehl CTL60, Руководство оператора, Страница: 120 / 170

Результаты поиска

Содержание CTL60

Отзывы: