Gehl CTL60 Скачать руководство пользователя страница 102

Страница: 102 / 170

100

MAINTENANCE

Walk-Around Inspection

Perform the following inspections once every day before starting the engine the first time.

WARNING

Before operating, perform the walk-around inspections and make repairs immediately
should any irregularities be found.

Be sure to secure the engine hood or rear door when opening it. Do not open the
engine hood or rear door on slopes or in strong wind.

Before starting the engine, look around the machine and lower body, clean any combustible
materials off high temperature parts of the engine, and inspect for such irregularities as oil
leakage, water leakage and looseness of nuts and bolts.

Inspecting by Opening the
Engine Hood and Rear Door

1. Check for any twigs, leaves, oil or other

combustible materials around the engine
and battery.

2. Check for oil or engine coolant water

leakage around the engine.

3. Check for oil leakage from the hydraulic

tank, hydraulic devices, hoses and
connections.

T7G0031

Содержание CTL60











































































































































































Результаты поиска

Содержание CTL60

Отзывы:

Gehl CTL60, Руководство оператора, Страница: 102 / 170

Результаты поиска

Содержание CTL60

Отзывы: