Gehl CTL60 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 170

Gehl CTL60 Скачать руководство пользователя страница 61

59

OPERATION

Starting and Stopping the Engine

Before Starting the Engine

1. Adjust the seat for a comfortable operating

position.

2. Fasten the seat belt.

3. Check that the safety bar is in the locked

position.

4. Check that the control levers and pedals

are in the neutral position.

5. Insert the key into the starter switch, turn

it to the ON position, then perform the
following inspection:

¡

All the warning lamps flash and an
alarm is sounded for 2 seconds. The
meters also start functioning. After 2
seconds, only the battery charge
warning lamp (4) and engine oil
pressure/coolant level warning lamp (2)
flash, and the other lamps turn off.

¡

Turn the light switch to check that the
front light, tail lights and meter light turn
on.

¡

Check the fuel level.

If a lamp does not light or the alarm is not
sounded, the bulb may be burnt out or a wire
may be damaged. Contact a Gehl sales or
service outlet for repairs.

T7B015

N

N

B

A

T7D002

PREHEAT

OFF

ON

START

E4D002

T7D0031

4

2

«
...
59
60
61
62
63
...
»

Содержание CTL60











































































































































































Отзывы:

Нет отзывов