GEA RedGenium Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 118

GEA RedGenium Скачать руководство пользователя страница 23

2.7

Personnel qualification

Qualification

All work explained in this manual (assembly, electrical connection, start-up, oper-
ation, etc.) may only be carried out by trained

technical personnel

who observe

the relevant technical regulations.

Technical personnel

are representatives of the product manufacturer and per-

sons who, as a result of their technical training, experience and personal instruc-
tion in training measures, have sufficient knowledge of:

•

applicable international and national standards,

•

applicable occupational safety regulations,

•

applicable accident prevention regulations,

•

applicable environmental protection regulations,

•

the construction and functioning of the product,

•

recognised technical regulations for safe work according to good professional
practice.

The technical personnel must:

•

be able to assess the work assigned to them, recognise and avoid possible
dangers,

•

be authorised by those responsible for the safety of the system to carry out
the requisite work and activities.

Caution!

No arbitrary changes may be made to the control or other components
belonging to the product.
► Maintenance work may only be done by authorised service staff.

Special requirements for the electrical technicians

Work on electrical components and modules may only be carried out by a

trained electrician

in accordance with the electrical engineering regulations. Fur-

thermore the operator has to take care that the electrical systems, tools and fix-
tures are operated according to the rules relevant to electrical engineering regula-
tions and applicable standards and are serviced properly.

•

In principle it is prohibited to carry out work on parts under voltage.

•

Fuses may only be replaced and not repaired or bypassed.

•

Only the fuses specified in the electrical circuit diagram may be used.

•

A two-pole voltage tester must be used to ensure that the parts are de-ener-
gised.

•

The power supply as well as the product casing must be sufficiently grounded
and tagged with a suitable label.

•

Deficiencies noticed in the electrical systems/modules/tools and fixtures must
be corrected immediately. If an acute danger exists before then, the product
must not be operated in the defective condition.

Safety

Personnel qualification

L_151511_2

19.12.2019

23

«
...
21
22
23
24
25
...
»

Содержание RedGenium























































































































Отзывы:

Нет отзывов