GEA RedGenium Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 118

GEA RedGenium Скачать руководство пользователя страница 111

12.4

Dismantling, disposal

Preparatory measures

Notice

Components removed must be disposed of correctly and according to legal
requirements.
► Components may be under excess pressure and must be depressurised
before opening.
► During decommissioning and disposal, it must be ensured that the vari-
ous materials are separated and passed on to the recycling system for fur-
ther processing.
► Disposal of component residues and components as domestic waste is
prohibited.
► In general, the legal regulations for the disposal of electrical equipment
applicable at the installation location must be considered.
► The information in Chapter "Decommissioning" must be observed.

•

Removal and disposal of the product must be carried out in such a way that:

–

the system is free of voltage and is protected against unintentional reacti-
vation,

–

accidents to persons are prevented,

–

material damage is prevented,

–

uncontrolled escape of refrigerant or oil is prevented.

•

Disposal and decommissioning work must only be carried out by personnel
which is qualified according to EN 13313.

•

In case of contact with refrigerant or operating media, their hazardous proper-
ties (e. g. toxicity, inflammability) must be taken into account (see also the
safety data sheet for the refrigerant). Personal protective equipment accord-
ing to EN 378-3 must be worn.

•

National regulations (e. g. EN 378-4, Section 6) must be observed for the
recovery and disposal of refrigerants.

•

National regulations (e. g. EN 378-4, Annex A) must be observed for the
recovery and disposal of operating media (oil).

•

No unauthorised persons must be within the installation area of the plant dur-
ing decommissioning, as they could come into contact with refrigerant.

•

All components of the plant which are not to be re-used, as well as refrigerant
and operating media, must be stored in suitable separate containers. They
must be treated as waste and disposed of safely.

Notice

Re-use of operating media is not possible!
► Operating media must be treated as waste and disposed of safely.

Decommissioning

Dismantling, disposal

L_151511_2

19.12.2019

111

«
...
109
110
111
112
113
...
»

Содержание RedGenium























































































































Отзывы:

Нет отзывов