GEA RedGenium Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 118

GEA RedGenium Скачать руководство пользователя страница 102

10.4.14 Maintenance of the compressor drive motor

Notice

Maintenance of the compressor drive motor must be carried out in accord-
ance with the "Motor documentation".
► The motor documentation is part of the product documentation.

The maintenance of the compressor drive motor includes the following activities:

•

Lubrication of the motor
Lubrication intervals and amounts according to the "motor documentation" or
"nameplate".

•

Cleaning the motor (externally)
Selection of a suitable cleaning agent according to the motor documentation.

10.4.15 Checking the operating parameters

Notice

The checking intervals recommended in the table must be observed.
► The control of the operating parameters is carried out via a Touch Panel.
The project-related setting values and limits are given in the parameter list.
► Inform the GEA Refrigeration Germany GmbH technical customer serv-
ice if the parameters are outside of the permissible limits.

Checking the operating parameters

Parameter to be checked

Every 24 to

72 h

Weekly

Monthly

Remark

Discharge temperature

X

Maximum discharge temperature 150 °C, in individual
cases (e.g. heat pump applications) this may be exceeded
in agreement with the manufacturer.

Oil temperature

X

See parameter list!
The viscosity must not be less than 10cSt.

Oil pressure

X

The oil difference pressure to the discharge pressure
must not be lower than 1.7 bar. In the event of an oil dif-
ference pressure fault, a contaminated oil filter may be the
cause.

Compression discharge
pressure

X

See project value (parameter list). Determine the super-
heat temperature on the pressure side by comparison with
the final discharge temperature.

Oil level in compressor

X

An oil level must be visible in the sight glass at all times. If
the oil level is below the bottom third of the sight glass,
refill oil.

Oil heater

X

When compressor is shut down, the heater must automat-
ically start.

Setting the safety devices

X

See the setting values in the parameter list.

Number of operating hours

X

See maintenance instructions for maintenance work to be
carried out according to the number of operating hours.

Maintenance

Maintenance work

L_151511_2

102

19.12.2019

«
...
100
101
102
103
104
...
»

Содержание RedGenium























































































































Отзывы:

Нет отзывов