GE ZIC30GN Скачать руководство пользователя

Страница: 55 / 83

– 55 –

Water Valve

The water valve is serviceable from the front of the
unit. To access or replace the icemaker water valve,
it is necessary to remove the toekick and vent panel.

The water valve coil has an approximate resistance
value of 180

Ω

To replace the water valve:

1. Remove the toekick and vent panel. (See

Toekick

and Vent Panel

2. Remove the water valve inlet tubing from the

water valve.

3. Remove the 2 Phillips-head screws and lock

washers that attach the water valve to the
cabinet.

4. Rotate the water valve counterclockwise and

pull the valve out of the cabinet.

Water Valve

Water Valve Inlet Tubing

5. Press the John Guest connector collar and

remove the

ﬁ

lter inlet tube from the water valve.

6. Press the John Guest connector collar and

remove the

ﬁ

lter outlet tube from the union

connector.

7. Remove

the

ﬁ

lter outlet tube and clip from the

water valve bracket.

8. Disconnect the 2 wires from the water valve.

Filter

Inlet

Tube

Filter Outlet Tube

Disconnect

Clip

John Guest Connector Collar

Union Connector

John Guest Connector Collar

https://appliancetechmanuals.com

Содержание ZIC30GN




















































































Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды

GE ZIC30GN, Техническое обслуживание руководство

Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды