GE ZIC30GN Скачать руководство пользователя страница 15

Страница: 15 / 83

– 15 –

Adjust the screw posts up or down under the bracket
on top of the door to level the panel.

Lock the panel to the door by installing the nuts

provided onto the screw posts on top of the door.
Next , screw the L-bracket provided into the bottom of
the door and the panel.

Hooks

Top of

Fresh Food
Panel Door

Nut

Slots

Bracket

Screw Post

Bracket

Freezer
Drawer

Back View of Panel Hooks and Bracket

Fresh

Food
Door

Convertible

drawer

Freezer
Drawer

The lower brackets on the Fresh Food & Convertible Drawer

should not be installed until after the panel is in place.

STEP 13 START ICEMAKER

• Press the

ZONE

indicator on the control pad twice

to select the freezer drawer. Press the

ICE

icon on the

right side of the control. A line will appear under

ICE

show that the icemaker is ON.

• Be sure nothing interferes with the sweep of the feeler

arm.

• Discard the f irst full bucket of ice cubes.

• To turn the icemaker off, press the

ICE

icon. The word

OFF

appears below

ICE

to show that the icemaker

is OFF.

https://appliancetechmanuals.com

Содержание ZIC30GN




















































































Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды

GE ZIC30GN, Техническое обслуживание руководство

Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды