GE ZIC30GN Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 83

background image

– 41 –

Evaporator Thermistor

The evaporator thermistor is inserted into a holder
in the top of the evaporator. The evaporator
cover must be removed to access the evaporator
thermistor. (See

Fresh Food Evaporator Cover

.)

Silicone Grease

Note:

When replacing the evaporator thermistor,

splice a new thermistor into the harness using
connectors and procedures approved for damp/wet
conditions.

Thermistor

Fresh Food Fan Motor

The fresh food fan motor is a variable speed, PWM
(pulse-width modulated), 12-VDC motor with rpm
feedback to the main board. The fan motor is
located above the evaporator in a recess in the back
wall of the fresh food compartment. To access the
fan motor, it is necessary to remove the evaporator
cover.

To remove the fresh food fan motor:

1. Remove the evaporator cover. (See

Fresh Food

Evaporator Cover

.)

2. Peel back the tape and disconnect the fan

motor wire harness.

3. Remove the 3 Phillips-head screws that attach

the fan motor to the recess in back wall.

Disconnect

Tape

Note:

The fresh food fan motor will run on a 9-volt

battery for testing purposes. Use jumper wires to
connect the red fan wire to the positive battery
terminal and the blue fan wire to the negative
battery terminal.

https://appliancetechmanuals.com

«
...
39
40
41
42
43
...
»

Содержание ZIC30GN




















































































Отзывы:

Нет отзывов

Похожие инструкции для ZIC30GN

Бренд: U-Line Страницы: 2

Бренд: U-Line Страницы: 2

Бренд: Zanussi Страницы: 8

Бренд: Zanussi Страницы: 36

Бренд: Zanussi Страницы: 24

Бренд: Zanussi Страницы: 20

Бренд: Zanussi Страницы: 24

Бренд: True Страницы: 2

Бренд: WARREN-SHERER Страницы: 17

Бренд: Kairak Страницы: 30

Бренд: Nextel Страницы: 12

Isotherm Drawer 190

Бренд: Indel Webasto Страницы: 7

Бренд: Landmark Страницы: 32

Бренд: JUNO Страницы: 14

Бренд: Gibson Страницы: 19

Бренд: Amana Страницы: 21

Бренд: Grundig Страницы: 43

Бренд: SEVERIN Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды