GE ZIC30GN Скачать руководство пользователя страница 40

Страница: 40 / 83

– 40 –

Defrost Heater

The evaporator uses a wraparound serpentine
defrost heater. The evaporator is attached to 4
brackets on the re

ﬂ

ective heat shield. To access

the defrost heater, it is necessary to remove the
evaporator cover.

To remove the fresh food defrost heater:

1. Remove the evaporator cover. (See

Fresh Food

Evaporator Cover

2. Pull the defrost drain heater out of the drain.

(See

Defrost Drain Heater

, this section

Note:

In the following step, a Styrofoam air block is

located behind each re

ﬂ

ective tape.

3. Peel back the 4 re

ﬂ

ective tapes and remove the

4 air blocks from the sides of the evaporator.

4. Open the 7 crimped tabs located along the

bottom of the defrost heater.

Reﬂ ective Tapes

Crimped Tab (1 of 7)

(

Continued next page

)

5. Disconnect the defrost heater connector.

6. Remove the Phillips-head screw, 7-mm nut, 3

lock washers, ground wires, and clamp from the
defrost heater.

7. Remove the 7 clips that attach the heater to the

evaporator.

9. Lift the evaporator from the 4 brackets on the

ﬂ

ective heat shield.

10. Carefully pull the defrost heater off the front and

back of the evaporator.

8. Remove the 2 plastic ties from the bottom of the

heater.

Clamp

Clip (1 of 7)

Defrost Heater

Connector

https://appliancetechmanuals.com

Содержание ZIC30GN




















































































Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды

GE ZIC30GN, Техническое обслуживание руководство

Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды