GE ZIC30GN Скачать руководство пользователя

Страница: 54 / 83

– 54 –

4. Attach the capillary tubing to the copper

extension tube using the WR97X10035 (5/16-in.
to .079) capillary-reducing connector.

Note:

When using a capillary-reducing connector,

make sure the capillary tube protrudes thru the
opposite end of the connector.

5. Since this connector does not have an internal

stop, bend the capillary tube slightly at the
opening to create a stop.

6. Pull the capillary tube out 1/8 inch, apply a

single drop of LokPrep, and reinsert before
compression.

Bend

Protrusion

Compressed Reducer

Extension Tube

Removed Tubing

4. Lift the toekick off the bottom 2 tabs.

Toekick and Vent Panel

The toekick and vent panel must be removed to
access the system tray.

To remove the toekick and vent panel:

Note:

Installation instructions permit a removable

wood toekick panel to be installed on the unit
provided it is secured with Velcro® or magnets.

1. Remove the wood or stainless steel convertible

drawer panel. (See

Installation Instructions

2. Insert a large,

ﬂ

at blade screwdriver between

the top of the toekick and the bottom of the vent
panel, as shown in the photo below.

3. Push the screwdriver down while pulling out the

top of the vent panel. Repeat on opposite side.

Tab

5. Remove the 2 Phillips-head screws from the

bottom and 2 recessed Phillips-head screws
from the top of the vent panel.

https://appliancetechmanuals.com

Содержание ZIC30GN




















































































Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды

GE ZIC30GN, Техническое обслуживание руководство

Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды