GE ZIC30GN Скачать руководство пользователя страница 57

Страница: 57 / 83

– 57 –

(

Continued next page

)

Power Supply and Main Control Board
Assembly

The power supply and main control boards are

installed in a housing located on the right side of
the system tray. The toeplate and vent panel must
be removed to access the power supply and main
control board assembly. (See

Toekick and Vent Panel

The power supply and main control board assembly

is ordered as a single part number.

To remove the power supply and main control

board assembly:

1. Remove the toeplate and vent panel. (See

Toekick and Vent Panel

2. Remove the 2 Phillips-head screws that

attach the power supply and main control
board assembly to the right side of the center
compartment.

Caution:

In the following step, to avoid damage to

wiring, monitor the power supply and main control
board assembly wiring as the assembly is pulled
completely out of the system tray.

3. Pull the power supply and main control board

assembly forward out of the cabinet.

Power Supply and

Main Control Board

Assembly

Power Supply Board

To access the power supply board, it is necessary to

remove 6 Phillips-head screws and the front cover
from the housing.

The power supply board is attached to the inside of

the control housing with 4 Phillips-head screws and
connected with 3 wire harnesses.

Front Cover

https://appliancetechmanuals.com

Содержание ZIC30GN




















































































Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды

GE ZIC30GN, Техническое обслуживание руководство

Результаты поиска

Содержание ZIC30GN

Отзывы:

Похожие инструкции для ZIC30GN

Бренды по названию

Популярные бренды