GE VAT200 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 117

background image

Chapter 0 Preface

0-1

Chapter 0 Preface

0.1 Preface

To extend the performance of the product and ensure your safety, please read this manual
thoroughly before using the inverter. Should there be any problem in using the product
and can not be solved with the information provided in the manual, contact your nearest
GE’s distributor or our sales representatives who will be willing to help you. Please keep
using GE’s products in the future.

※

※

※

※

Precautions

The inverter is an electrical electronic product. For your safety, there are symbols such as
“Danger”, “Caution” in this manual to remind you to pay attention to safety instructions
on handling, installing, operating, and checking the inverter. Be sure to follow the
instructions for highest safety.

Danger

Indicates a potential hazard could cause death or serious personal injury
if misused.

Caution

Indicates that the inverter or the mechanical system might be damaged
if misused.

Danger

Do not touch any circuit boards or components if the charging indicator is still lit after
turned the power off.

Do not wire when the inverter is electrified. Do not check parts and signals on circuit boards
during the inverter operation.

Do not disassemble the inverter and modify internal wires, circuits and parts.

Ground the ground terminal of the inverter properly. As for 200V class ground to 100

Ω

or

below, 400v class ground to 10

Ω

or below.

Caution

Do not perform a voltage test on parts inside the inverter. High voltage will easily destroy
these semiconductor parts.

Do not connect T1 (U), T2 (V), and T3 (W) terminals of the inverter to AC power supply.

CMOS ICs on the inverter’s main board are susceptible to static electricity. Do not touch
the main circuit board

0.2

Products Inspection

GE’s

inverters are all passed the function test before delivery. Please check the followings

when you received and unpacked the inverter:

The model and capacity of the inverter are the same as those specified in your purchase order.

Check where there are any damages caused by transportation. Please do not apply the power, and do

contact GE’s sales representatives if any of the above problems happened.

«
...
3
4
5
6
7
...
»

Содержание VAT200






















































































































Отзывы:

Нет отзывов

Похожие инструкции для VAT200

Бренд: YASKAWA Страницы: 81

Fcontrol Basic FSDM Series

Бренд: ZIEHL-ABEGG Страницы: 30

Бренд: RHINO MOTION CONTROLS Страницы: 10

Бренд: Danfoss Страницы: 8

FRENIC-Lift LM2A Series

Бренд: Fuji Electric Страницы: 73

Бренд: Bosch Страницы: 80

Бренд: Teac Страницы: 1

Presario V3000 - Notebook PC

Бренд: Compaq Страницы: 16

Бренд: ADS Страницы: 23

Бренд: Stober Страницы: 74

CACR-HR BAB Series

Бренд: YASKAWA Страницы: 293

Бренд: Afag Страницы: 19

Бренд: Rexnord Страницы: 7

Бренд: Melco Страницы: 12

HAUTAU SKA 50-500

Бренд: Maco Страницы: 12

Бренд: IBM Страницы: 54

Бренд: ABB Страницы: 42

Бренд: Danaher Motion Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды