GE lp33 20 series Скачать руководство пользователя страница 34

Страница: 34 / 43

Critical Power

Modifications reserved

Page 34/43

GE_UPS_ISG_LPS_3UL_20K_30K_2US_V010.docx

Installation Guide

LP33 Series 20 & 30 UL S2

4.9.5

UPS functioning as frequency converter

NOTE !

The set-up for

LP33 Series 20 & 30

when functioning as frequency converter requires

a partic

ular installation and adequate setting of some parameters (accessible

only through password), and can therefore only be done by a

GE QUALIFIED

SERVICE ENGINEER

The

LP33 Series 20 & 30

can run as frequency converter only with a connected

battery, as a standard UPS.

When the UPS

LP33 Series 20 & 30

is delivered as frequency converter (different output frequency with

respect to the input frequency),

the automatic bypass and manual bypass functions are disabled

Therefore the

load

cannot be transferred to mains in case of overload, short circuit, or inverter failure.

In cases where the UPS needs to be powered down for maintenance purposes, the critical load must
also be powered down during this time.

When the set-up parameters of the UPS are set for

frequency converter

, the

ECO Mode

operation is

automatically disabled.

The UPS delivered as

frequency converter

has the following differences:



Automatic

bypass disabled

by setting of dedicated parameter (access protected by password

reserved to service engineer).



The handle of the switch

Q2 - manual bypass

is removed to avoid accidental wrong manipulations.



Mains bypass

disabled by removing the fuse

fitted on the board

P2 – Power Supply

WARNING !

In case a UPS delivered as frequency converter should be set on site for UPS
standard version, the operation must be performed by a QUALIFIED SERVICE
ENGINEER.

Notices for installation:



For UPS with

common AC input

follow the standard procedure described in

Section 4.9.1

Notices for start-up procedures:



Follow the standard procedure indicated in

User Manual

Notices for shut-down procedures:



Follow the standard procedure indicated in

User Manual

NOTE !

The inverter can be turned off only by pressing the

“Load Off”

key.

Содержание lp33 20 series












































Результаты поиска

Содержание lp33 20 series

Отзывы:

Похожие инструкции для lp33 20 series

Бренды по названию

Популярные бренды

GE lp33 20 series, Руководство по установке

Результаты поиска

Содержание lp33 20 series

Отзывы:

Похожие инструкции для lp33 20 series

Бренды по названию

Популярные бренды